NEO-TEC NS8105 Gas Chainsaw Fit for 36''/42'' Guide Bar Chain,2-Cycle Power Head 105cc Power Chain Saw 4.8KW 6.5HP Gasoline Chainsaws,All Parts Compatible with G070 070 090

I bought this saw after moving onto a small piece of property with lots of large oaks. I knew that I would be dealing with down trees occasionally and would need a large saw. I simply don't run it enough to justify paying 3x the cost for a Stihl, so I rolled the dice with this one. I have cut a few large fallen trees (3-5 foot diameter, 1 fir and 2 large oak) and this thing eats them all without issue!! This saw is an absolute beast!!! Fair warning though... this is a heavy saw and is a workout to use! Also...make SURE you use the compression release when starting it!

DO NOT BUY! Bought this chainsaw back in November. Followed the break in instructions for getting it going and tuning etc. Ran 3 tanks of premix through it cutting a tree up with no issues just seemed a bit low power but i was easy on it to break it in. Got it back out 2 days ago and ran half a tank through it before it started acting funny at full throttle. Noticed the high throttle screw had vibrated all the way out and was missing. Contacted neotec to try and get the screw size through Amazon and their website where it says 24 hour response time. Never heard anything back from neotec on here or their site. Drove 45 mins to lowes to get a screw. Tuned it again per instructions. Before that tank ran out (4th tank in the chainsaw ever) it started smoking. I killed it and took it to a chainsaw sales and repair dealer. They determined there was a manufacturing issue with the bar (42") and/or chain that caused the clutch to overheat and the bar, chain, clutch are unusable and they tested the cylinder and said it has low/no compression. Just spend the extra money on a name brand. At the very minimum you'll be able to get a response if you have issues.

This chainsaw is huge! I love it! Started just fine & runs good. Cuts like I beast! Unstoppable. Perfect for big timber. Takes some strength to handle it.

Es lento pero seguro tienes que estar fuerte porque es pesado para mí es excelente

great job for the money after breaking. headed to end up and it rips works excellent it'll be nice if I automatic oiler so you don't have to worry about that pumping it and if you tip it on the side it does leak out of the oil pumper otherwise it's good to go

I read a lot of reviews prior to buying. I purchased this saw in Oct 2022. I did a review on the Garwinner 20” 62cc saw (love that saw too). There is a learning curve with this saw. 1. Don’t pull the throttle before it starts. 2. Pull the choke fully out and pull until you get a pop. 3. Push choke half way in and it should fire right up. You still need to hold down the decompression valve and etc. as the directions state. I have some flooding issues at first, hence is why I wrote do not pull the throttle while starting of before trying to start. I love the full chisel chain that it comes with. I use it to plank out large logs. I have fell one tree and bucked it. It is a heavy saw compare to your 20” saws. Roughly 30 lbs. It has been great for me. I’m an average size man and can start it fairly easy. The saw sat over the winter and fired up on the fourth pull. The initial pull on full choke, second pull on full choke and got the pop, move to half choke and turned over and stalled, and no choke with start up two days ago. I highly suggest hearing protection, the muffler is wide open and is extremely loud. I think it’s 105-115 dB. I will be using it a lot more this year and will do another review with an update maybe around autumn or so. This saw needs a check on the bar oil before refueling. I hope this helps you out.

cannot rate as yet since I did not receive a manual with it and so have no direction on how to start, maintain or use this saw....could I please get a manual sent to me????

Brand New out of the box and it took 3 days to finally get it to start.Once it started, it ran decently. I didn't like the sound but it seemed super sensitive to any bit of adjustment, so I left it where it started because it comes setup for running for the first three tanks of fuel.Annoying popping sound aside, it ran good and it cut like a dream, to be honest... made my other saws look like junk, including my Rancher.However, I spent the entire next day trying to start the saw on it's second tank of fuel with no success.The first pull was the only pull that sounded like it would start with the next pull; it never did.Brand New Bosch "Start" spark plug came in it but there's nothing in the User's Manual about the proper spark plug gap.Definitely getting a charge to the spark plug and I've repeatedly gone through the steps for a "wet" plug/flooded combustion chamber, but still will not crank.As wonderful as the saw was the one time it did run, I still cannot give it more than a single star.All of the hours and sweat lost trying to get the saw started completely negates how well it cuts big timber.If I can figure out the issue, then I'll update my rating and provide what I've learned.