VonHaus Tilt TV Wall Bracket for 37-82" Screens, Tilting Flat to Wall Mount with Quick Release Straps, 75kg Capacity, Max VESA: 400x600mm, for Curved and Flat TV's

Very strong bit of kit for a light frame. Used the same make before for my 55inch telly, this time I needed the right size for a brand new 65QNED87T6B LG. Fit perfectly and easy to put together. Had my last one for 8 years and never had one problem with it. Can't imagine having a issue eith this one either. Reliable.

I bought the 15deg tilting version, but had only seen pictures of the fixed version and my previous tilting bracket (a different manufacturer) so was a little disillusioned when it arrived. BOY is the packaging small.You have to assemble the 6 piece wall mounting bracket, it is not 1 piece (and 16screws with 12 nuts and a number of washers). This is quite fiddly and the instructions were on what may as well been A1000 paper size. The print was very small and the instructions a little difficult to follow so working out how it went together and which way up took a few moments thought and laying out on the floor to puzzle through.Anyway, with commonsense, some choice words and a careful part count the rectangular bracket is assembled.Word of advice, thing about which side to put the nut and which the bolt when making assembly. If you put the bolt through the wrong way, the access with a spanner to the nut is almost impossible. Doubly a problem with the "square bolt" x4 as this cannot be turned, so the only option is to rotate the nuts. At least with the other 8 nut and bolts there is a little more access so can be tighten when assembled either way, but trust me, one way with access to the nut is alot easier.Fixing to a brick wall requires dia. 10 drill bit and large spanner for the bolts. (sorry, cannot remember the size). Don't forget the washers before bolting to the bracket. The slots in the bracket are quite wide, so the washers help seat the bolts.Like always getting 4 fixings on the top and 2 on the bottom all in the correct place on the wall was not easy and even using my full length spirit level (not the blooming small thing supplied) it was hard work. The end result was a very slightly off horizontal bracket, which over the length does not look bad, but it gets exagerated with the TV. Mine was 50" and looked very lopsided prior to tweakingFine tuning of the squareness of the TV using the mounting to the bracket proved difficult, but not impossible.Due to the closeness/slimness of the mount make sure you put all the wires in the back of the TV before you offer it up to the mount.Tightening the 2 screws that hold the bottom of the bracket to the wall mount required a very long shafted screwdriver as access is limited to them also.I should have bought the zero deg non tilt version as have decided due to location that the tilt was not necessary. I could not achieve zero deg with the bracket so have a slight tilt, but that is my fault, not the brackets. What was the brackets fault is that I cannot get it to lock at 0deg, hence the small angle. I have not fault found why as was loosing wife appeal factor by now as it took more than 1 minute to put up. "why did you not buy the expensive one and geet it professionally fitted....?"BUT....For the price it does the job wonderfully, so despite the above, I feel that the price compensates for all of this, hence 5 stars. At the end of the day, I have a 50" TV on the wall at the angle I want at a very good price.It took all in all about 45mins to 1 hour to put up, including hunting for spanners, drill bits, working out the instructions etc. which actually I feel is very good time.

As others have written, instruction manual is atrocious and it's very difficult to see how the vertical brackets that make up the frame should fit together. I went for this bracket as it allowed the TV to mount slightly closer than the smallest size (up to 32"), but it is almost as wide and tall as the TV that it is supporting - something to bare in mind if aesthetics are important.Once assembled, mounting to the wall is very easy, it is very sturdy and does provide a close fit to the wall. The tilt brackets should be assembled as a mirror image, so you can adjust both angles more easily. I can see how it may block access to TV ports or make it difficult to get cables in or out, but that's not the fault of the bracket and the possible price you pay for having a TV only 35mm from the wall...

Ideal, easy to install and good quality for price.

Does the job, sturdy. I did however have to use some extra spacers from another TV bracket package to hang my Samsung 65" tv as the screws supplied were slightly too long. But for the price couldn't complain. Also to note once the bracket is up there is no adjustment to level it so it has to be bang on level. Some brackets have screws to adjust this.

Fantastic service and item is as explained.Done the job brilliantly and good quality

Done the job! great price 👍

Once fitted, this works well and is fit for purpose. However, the instructions are pictures only, no text, which are quite difficult to interpret.. More importantly, the 2 TV release pull cords are attached using very flimsy rings that pull off very easily, leaving a difficult job to access the release mechanisms themselves. We wasted about an hour before success using a bent length of wire to pull the release mechanisms to release the TV.