Bull Ring Inner Bed Retractable Truck Bed Tie Down Anchors, Built for 2007+ Chevy Silverado & GMC Sierra, 2015+ Chevy Colorado & GMC Canyon, Fits in Truck Bed Stake Pockets, Easy Installation, 9 Pack

Yes, they do indeed fit my 2025 Chevrolet Silverado Short Box with factory spray in bed liner. Amazon is wrong. Installing the first one took me about 15 minutes, the last was under one minute. My method was remove bolt completely, push metal backing plate fully back and the other part fully forward, push through hole, move the device up/down all the way to get it the rest of the way in. Pull ring out until it locks. Using the ring as a handle, repeat with the front part. Install bolt.I like these over the GM ones because the rung fully retracts and locks out. GMs do not retract at all. GM selling these as a 4 pack is irritating because my bed has 9 provisions for lock downs. And these were less than 1/3 the cost of the factory ones.

works well

Great product! Easy install… fantastic customer service!

Read the reviews good and bad. Amazon add said it would not fit on my vehicle, but if you follow the instructions it will fit. My bed had a factory spray bed coating which caused no problems with install. Once installed I used a 1/4 inch rope and pulled hard on it and it did not pop out. You could although see my bed wall moving in the direction I was pulling. I pulled at various angles and the mounting screw did loosen a slight bit. As a result, I added Locktite to all screws as part of my install process. Time will tell if the anchors will hold up to the 1000 lbs advertised, but after seeing my truck bed move I worry more about it failing. Why did I only give 4 stars? Once I have used the system and see how it holds up I will up grade or down grade accordingly.After the first anchor install (during which I did the pull test, plus decided to pull screw and use locktite) the remaining 8 anchors took less than 20 minutes to install. I did look at the other brand of the same design. It from the pictures and description does seem an improvement on the basic design, such as metal versus plastic.

After crossing my fingers that these would fit, I can now confirm that they fit and work great on a 2024 Chevrolet Colorado ZR2. But it’s tricky getting them mounted. Obviously take the plastic plug out of the truck’s oval hole that you want to put the bull ring into. On the Bullring, you have to first take the screw out completely. Then put the back through the hole threading the top of the silver steel plate through first and wiggling it until the whole silver steel plate is through the hole. Then pull out the ring holding the whole thing in place. Then hand screw the screw back into the bullring with your other hand. Tighten it up with a screwdriver.

The media could not be loaded. I had Bullrings in my previous trucks, and used them all the time. They work great! So I wanted to get these for a Silverado 2500. I was getting conflicting information if these were compatible with a 2024. I even contracted Bullring, and said they said it should be, but they had not tested it with a 2024. I can confirm these do fit a 2024 Silverado 2500. Simply pop the plastic cover off, loosen the screw, and place the hook in bottom first, and snap it up. The hook should pull up at a 45 degree angle. Tighten the screw, and that’s it. It took 15 min to do all 6 in the sides of my bed.

Fairly expensive for what they are but they're good quality. Installation is easy and they look nice when installed.

The media could not be loaded. Easy Installation with a Few Simple ToolsI recently installed these truck bed anchors and was impressed by how easy it was. I used a drill to make the necessary holes and a sharp knife to cut the plastic/liner out of the anchor ovals. Once the holes were drilled and the ovals were cut, I was able to install all 9 anchors quickly without any hassle. The anchors fit securely and are sturdy. Highly recommend these if you're looking for a straightforward installation and reliable anchors for your truck bed!