Thermaltake CA-1E7-00M6WN-01 Core P5 Tempered Glass Snow Edition ATX Wall-Mount Chassis for PC - White

Unconventional but beautiful case, with plenty of modularity for your chosen setup.Pros:-Good cable management options: loads of room in the rear area of the case to sensibly route cables, especially important since everything is on show.-General build quality is excellent: Good thick steel, everything just fits together really well.-So many options for so many setups: wall mountable, vertical or horizontal GPU mounting options, fits multiple motherboard sizes, multiple PSU orientations and sizes, radiator mounts for AIOs or full open loops.Cons:-Acrylic front panel: There is an optional tempered glass panel for another £40 but it would have been nice for a case that's all about looks to come with tempered glass as standard.-Vertical mounting with SLI setups can be tricky: not really the fault of the case, but trying to flex 2 pci-e riser cables is a faff.-Mounting a radiator will cost you some SSD bays: dependant on the size of rad you use, you will loose 1,2 or 3 SSD bays. You could still technically still mount SSDs in them but it'd block airflow pretty significantly. You still have access the twin HDD bays behind the mobo though (and m.2 if your mobo supports it)-Pointless magnetic dust filter: given that most radiator setups will push air through the case and out the back, the rear mounted dust filter is somewhat redundant, you could flip the fans and suck air through to the front, but generally that doesn't look as good (again this is all about asthetics, which is the key part of this case)

Note: Bought this case from another seller as my one from amazon arrived damaged.This case is a dream to work with. Everything but bolts on and fits perfectly. Currently using a push pull 240mm rad configuration and vertically mounted 750ti and there is still ample room for air flow. In the back, you are given about 5 cm of room for cable management, with an abundance of places to use ties and overlap on the case to route cables next to. The case was fairly easy to put together, instructions are a bit vague but the pictures and labels on the actual case make the process pretty straightforward.A little tip: if your acrylic panel arrived with paper protection, leave it in hot/warm water for 5 minutes and it will peel right off.Pros: Extremly easy to work with with great expandability, perfect for water cooled rigs.Cons:You will need to invest in quieter parts if pc noise bothers you as due to not encasing the components, there's is no noise dampening.The riser cable is known to be dodgy. Tip, use a spray can or other cylindrical object to make the bends in the cable. (Touch wood mine is fine at the moment)Also,not really a negative but if you are not using aio cooling or custom loops, find another case. This case will look empty without it.

Hi all.Bought this last year and it's really cool looking.BUTI've found the cable entry / exit holes are in the slightly wrong place, not large enough or don't have a rubber grommet.The hole for the PSU cables into the rear of the case is too small. The one for the CPU (top header) is too far right and the 24 pin is miles out for a nice flow on the loom.The GPU extender cable is too short by 100mm. If you want to add a card behind the GPU - It ain't happening as the extender cable runs diagonally from the MB port to the bottom of the GPU.For the money tho, I can't complain......LOL ;)The

I bought this case for the looks and because I want a wall-mounted PC, both for toddler avoidance and aesthetics. However, I was pleasantly surprised with the build quality- it's heavy and sturdy, with no flex or give in any of the panels. I expect it to outlast me! It presents my build very nicely.My only criticism would be the documentation- the included diagrams are VERY small and thus it can be difficult to work out the orientation of the included brackets etc.Also note if you want to wall mount this you will need a separate VESA mounting bracket.Update as I didn't mention at the time, the case came with a PCI riser cable which was faulty as supplied. Apparently a common issue according to Thermal take forums- however their customer support did not respond to me at all after several attempts. I ended up just buying a new riser from Amazon which solved the problem but overall made the case fairly expensive!

Good case, roomy, easy to work with and wall mounting was straight forward. Dropped a star because the PCI riser that came with it didn't work meaning I wasted time trying to figure out the problem and then I had to buy another (this is apparently an incredibly common thing with these, so be prepared for it).

Great product have had many of these cases and appear to all be of great quality and price however I was just going to buy this product when it went up by more than 10 pounds for no reason would love to have that taken of or refunded ;) but apart from that amazing product.

It's a tempered glass panel for your Core P3. Not really much to say. It's well packaged. Quite a bit weightier than the standard Perspex panel and is 'Smoked' a Grey colour unlike in the stock pics. The little rubber grommets come pre-installed putting it on is a doddle. Looks absolutely fantastic

Been running my PC for a while now in this case. Works as expected, I've a minimalist rig so suits me fine, probably wouldn't suit for someone with a DVD-ROM / fan controller requirement so much.