EZ FAUX DECORPeel and Stick Stainless Steel Wrap for Appliances Vinyl Dishwasher Cover 26" X 36" Easy Cut to fit, Waterproof, Heat, Scratch Resistant, Durable

I ordered this based on other reviews that stated it’s very close in color and texture to “real stainless” type appliances- and that part did not disappoint, it blends right in with my other items. It was the perfect size for my dishwasher to get it covered exactly… I used the “wet method” to apply it and at first it didn’t seem to want to stick so then I broke out the hair dryer to get it solidified and really stretch it around the corners. That worked out nicely and seems sticky enough for now, couple of bubbles but you don’t notice unless you get right up on it and look for them.Overall happy with this! Does the trick, here’s to hoping it lasts a good long while.

I bought this to update appliances and it did exactly that!. It was easy to install. The key is to spray on the water with a spray bottle and then use the padded scraper to remove any air bubbles. I applied it like 3 months ago and it is still stuck. My oven has a window that I covered and the stainless steel doesn't get hot at all. I would definitely recommend.

I took a chance on this one. We had a white dishwasher, and we got a new refrigerator and oven that are now stainless steel. The dishwasher works great, and is pretty new, so I did not want to waste money on replacing. I tried this stainless steel dishwasher sticker, and it looks great. Lots of money saved!Note - it is a really good idea to remove the panel from the dishwasher, and then apply the sticker. My front panel came off with (4) phillips screws. I applied the sticker and smoothed it out with the included spreader. The piece was the right size, plus a little, which was good. I applied for the front, and rounded the corners to cover the sides. When I screwed the piece back onto my dishwasher, it looked GREAT.I was/am very impressed. Thank you - definately worth the money!

The mixed reviews regarding this product's "ease of application" are well deserved. I bought one, applied it with poor results, then bought another and got great results. The finished look--once I actually got there--is very close to stainless minus just a bit of the shine. Here's the trick that I learned after my first fail:This product is basically just a large sticker. But the material is thicker than other types of stickers, and it can actually crease or "crack" (so to speak) if you bend it just a little too much. It also comes rolled up very tightly. These two features make it pretty difficult to apply: as you try to adhere it, it tends to roll back up on itself, and when you try to adjust it, it's very easy to create bubbles, or worse, crease it and damage the finish. When this happens (like it did for me), finishing the job becomes a moot point, since what you end up with looks like a stainless steel appliance with deep gouges in it.The second time around, I took the tightly rolled product I got in the mail and hung it from an indoor clothesline for 2 days, with a little bit of weight attached to help pull it straight (I didn't worry about the slight "lifting" of the surface material from the backing as it unrolled, and it didn't end up mattering). Unlike the first time, it was nearly flat when I went to adhere it, rather than rolled up . Then, starting from the upper right corner of my dishwasher, I peeled the backing a little bit at a time on a 45 degree angle (from top right to bottom left), pressing diagonally (from bottom right to top left) as I went along.This was both WAY easier than the spray-bottle method recommended in the instructions (which didn't help at all in round 1), and produced great results (no creases, no bubbles, just a look almost indistinguishable from real stainless).In the end, then, this is a pretty solid product, assuming you can get it on without wrecking it. Hopefully this will help with that.

This product is amazing! We covered our white dishwasher 2 years ago, and it still looks perfect. It has held up to daily use, and still looks like it did the day we covered it. No one would ever guess it was not stainless steel. It was slightly tricky to install. I recommend having two people, one who peels, and the other who smooths it down as ot is applied. Watch videos and you will get the idea. We did use the scrap pieces to trim out the top, and above the controls separately, carefully trimming and tucking the excess into the panels. No need to go out and purchase new appliances!