AUTOWIKI Fog Light Assembly For Toyota Tacoma 2016-2023 (Fits SR, SR5 Model Only) OEM Replacement Fog Lamps With Clear Lens 2pcs

I did a lot of research before I got this kit to install on my '23 Tacoma SR. It was the best option out there and fairly simple to install. No dealership wanted to mess with wiring in fog lights, so I did!The hardest part is getting the switch wire through the firewall. Be sure to thread inside the grommet. You probably won't need that red extension line at all. I taped up the power cable for the lights with some electrical tape to reinforce and zip tied some of the looser wires between the lights themselves. You have to push the switch in firmly but it's fun to do. Just be sure to get the correct add-a-fuse for the switch. I need a low profile mini.

This kit is very easy to install and very wallet friendly. This kit comes with 2 set of harnesses, light bulbs, front cover plates, fog lights unit and 1 paper instruction. If this is your first time install fog lights then I'd recommend watch the video in the listing by Autowiki first before dive into installing. Instruction is easy to follow for the engine bay area but make sure to connect the 1st wire harness properly i.e. connect the short wire to fog light unit closest to battery then connect other light unit. After that connect both red and black directly to battery for this 1st set of harnesses to power the bulbs. And then I think the harder part is to get the yellow wire thru firewall and connect the wires inside of the vehicle. I did a little trick by using a body of pen inserted to the rubber grommet where all other oem wires go thru firewall because i don't want to drill a new hole. Then I insert the yellow wire thru it and pull from inside the vehicle. Once inside, then you can use the 2nd set of harness to connect to the included button that can fit into one of oem button location. Carefully remove the left kick panel by driver side to gain more wiring room in the vehicle. Then connect yellow wire to yellow wire, black to body of the vehicle, green connector is to switch button and finally the red one is a bit tricky. Red wire according to Autowiki is for power source or accessories so it must connect to power source that can be turn ON or OFF, not ON the entire time. So do NOT connect red wire directly to battery. My trick for this is by using power source of cabin/bed light with switch button is just next to my fog light button. So I use a T-tap connector to connect the red wire to a green wire (I'd recommend test each wire to see which will power up the fog lights.) Once fog lights is powered up and can be turn on or off then adjust the angle of the beam on the light units. After that make sure everything is secured back to its location properly and extra wire must be secured away or else could tangle with your foot. Good luck on your project and learning at same time. Cheers.

plastic housings don't fit snugly but, not noticeable at a glance.

I Watched an Autowiki youtube video on the install, which made it very easy. Installed on a 2019 Tacoma SR that had no fog lights from the factory. Everything lined up perfectly, packaging was intact with no issues, wiring install went fine,(the trick with the screwdriver through the firewall to pull the wiring back through was very helpful!). Have not lit them up yet as I am waiting for the blue light switch to show up from Tacomalifestyle.com. My switch is the "Sasquatch Lights" one. Did not want the green light. The bevels fit like they are supposed to, with a little adjustment from the inside to get the clip to grab, but not an issue, nice and tight! Very happy, would definable recommend this product and this company. Did I mention that shipping was only 4 days?

The quality is alright. Highly recommend buying a low profile fuse tap to add in the power. P/Outlet 1 is the fuse I used to wire these lights up. The Trim pieces that come with it aren't flush, there is no mounting screws attached. As well the switch that comes with this unit to turn the fog lights on and off is basically defective. it takes multiple presses to get it to turn on and stay on, but it turns off no problem. Overall not a terrible buy. But I recommend you be cautious of the issues I encountered above. Also don't bother calling the support phone number there's no voicemail box attached, the website provided doesn't resolve to a valid domain.

Easy install, and looks great.

Installed on a 2021 Tacoma SR utility package. Install easy and straightforward. With exception of fuse tap, this is a very plug and play package.Bezels are not the best fit, but have not come loose or had any issues. Beam pattern very consistent and in my case, lines up perfect with low beams.If you’re looking for a basic fog light to add to your SR trim, this is a great and cost effective option. Since the bulbs are standard H11, you can upgrade performance to higher intensity halogen or LED later.

mine is a 2021 Tacoma SR5. I was replacing existing factory fog lights that had melted so I did not need the black plastic bezel or the wiring that came with it but I could not find just the light buckets available. the replacement was quick and easy. it was all done from the top-side with the hood open. there was no need to remove any wheel well liners or access panels under the truck. the hardest part was fishing the old one out of the bumper and getting the new one down to the install location. it is tight but if you can play tetris, you can figure it out. the removal and install is as easy as removing 1 screw, removing the light bucket from the factory bezel, snapping the new one in place, replacing the one screw and plugging it back in. aiming them can be a little tricky, but a stubby #2 phillips screwdriver is the tool you need and again it is all done from above with the hood open.

Installation facile, satisfait. Arrivé à la date indiquée. MERCI !

Installation was easy. Everything fit perfectly, I suspect people that had problems installing did so incorrectly.

I installed the fog lights. Then I put the bezels in... poor fitment. They don't clip in. They literally sit there barely holding on. For the price of the kit... it was workable, but I ended up using a couple dabs of gorilla crazy glue gel to hold the bezels in at the tabs to make up for the slop.A few months of good operation have gone by and I've improved my rating to 4 stars. I'm only running these until I can install a push bumper, so I can live with it. Otherwise I'm pretty picky about what goes onto my Tacoma. I like quality, which is why I bought a Toyota.Also, I wouldn't recommend leaving the relay and fuse exposed under the hood as they are not waterproof. I tucked mine into the factory underhood fuse box. By doing this, use the factory routing in and out of the fuse box for wiring. Don't just pinch the wires under the lid and expose the inside of the fuse box to contamination at the sametime like I saw some install videos on YouTube suggest.Tie the relay on trigger wire into the under hood fuse box running lights via a fuse tap to have the fog lights come on and off automatically with the other lights when the fog light switch is left on inside the cab.Finally, if you're like me and bought a factory style in dash fog light switch to maintain a factory appearance. Tie the illumination for the switch into the illumination of a nearby switch otherwise you'll have the switch at full brightness instead of dimming with the dash lights. Which in town isn't bad, but out of town it's super bright and irritating otherwise. Plus, it looks amateur. I like to keep every mod looking professional and like it came that way from the factory.With that all said, enjoy your new fog lights.

Nice fit on the truck but would have been nice to have better bulbs in them as have ordered new ones

I purchased December 2023 for a 2016 tacoma you sent a replacement for the right bulb with in a week of changing the right bild the left bulb burned out. I took those photos in July and have been avoiding making this second post.