Mini WiFi Router/Wireless Bridge Ethernet WiFi Hotspot Signal AP for Internet Connection Network Devices VAR11N-300

This device does exactly what it says on the tin. In my case, that was to set it up as an ethernet to WiFi bridge to my main broadband router (that supplies our internet connectivity) for my Humax DTR-T1000 Youview box, which only has an ethernet network connection, as I wanted to move it to another room where there was no physical network connection. The instruction booklet that came with it covered all the options that this device was capable of and was fairly well written and easy to understand. Within a very short time, I managed to set the device up as bridge/repeater (but I also chose to suppress its associated hotspot that was also available) back to/for my main router (using my smartphone to connect to it initially) then rebooted the device to change its configuration. I finally unplugged it from the USB power connection I was using (just for power) and plugged both cables into the T1000's ethernet and USB ports on its rear. It immediately powered up and "voila!", internet connectivity wirelessly back to my broadband connection. Excellent device and great value for what it does. I can't recommend this highly enough for what it does. (see photo)

Needed to enable Echo on University WiFi - works straight away - no messing

I had a Sky+ box and smart TV, each connected to a separate power link Ethernet cable - the Sky box is old tech and requires a "wired" connection and the TV has terrible builtin WiFi, and the power link devices suffer from poor electrical wiring in that part of the house so they are also rubbish. This device comes with less than obvious instructions, but here is what worked for me... It can be configured in all sorts of ways, but what I needed was the Bridge/Repeater mode configuration. This is fairly easy - plug both the Ethernet and USB (for power) cables into a computer then open a browser pointing at 192.168.253.254 and enter userid/password as admin/admin then select the Operating Mode tab and change from Router to WiFi Bridge + Signal Repeater mode, click Apply then Reboot. When it comes back login again and it should should show wireless connections, select your own router then click Next and supply the router password (as in the one printed on the back of the actual router). It then requires that you press Reboot and this is where the instructions get vague... the lights on the unit will start to flash, indicating all is well, but your browser page will never refresh. Don't worry - its good to go now. I then plugged the USB and Ethernet cables into the Sky box, thereby fooling it that it had a wired connection and reconfigured the TV to use the "new router" which is the same as the old router name plus an additional suffix. The signal from this device is awesome and both Sky box and TV now have great internet connections.

Heap of rubbish - instructions garbage, and after 90 minutes of faffing around and not getting connection I decided to return it.

Bought this mini router as a cheap WiFi to Ethernet bridge to get a Windows 10 PC without a WiFi adapter into a Hotel wireless broadband. Had to use my laptop to configure it, find the admin credentials in the (tiny print) manual, and select the right options from the extensive screens. Once successfully connected to the WAN, it works flawlessly and reliably, too much blinking, would be nice to reduce the LED usage sometimes. The form factor is minimal, much smaller than I expected but cable length sufficient to connect to a back pane. There are Wizards for most functionality usually to be found only in more expensive routers. A decent piece of hardware well worth the price.

Not easy to set up because documentation is poorly written. Explanation of setting up is ambiguous, and English appears to suffer from using cut and paste with a translation program. Once set up, works reliably. LED lights far too bright.

It's slightly fiddly to set up, and the speeds aren't great. But it does fix a problem where a single device has Ethernet but no Wi-Fi

Good little unit, being used as a wifi bridge to connect an HP printer with only ethernet connection, which is not easily accessible to the network in our new house. The documentation for the unit is a bit sketchy, but I managed to get it working with the wizard and a few tweaks / tries to connect. Once working seems solid and provides a decent connection for the purpose.

My Beringer X-air 12 mixer has a very inadequate WiFi that let massive interference when there was a lot of WiFi going on. This item cured the problem and haven't had a problem since. Five stars ⭐⭐⭐⭐⭐

使いやすい

Flashing led Lights are too bright and are not usable for astro imaging. Have painted top of container with Black permanent marker to try to reduce light. If I used electrical tape that would inhibit natural cooling that is if it generates any heat? A star/nebula could take 0hrs to 3+ hrs to image. Smaller led's Any other ideas to also reduce power consumption to decrease battery drainage. Daylight shooting a big 5 stars. ***** Night Astronomy With led brightness greatly reduced 5 Stars ***** Modem is small and light, Connecting leads are a good length for Aisair plus. Anyway to fix led intensity suggestions would be great appreciated.

Fonctionne de manière optimale.

Easily configured as a wifi bridge using the provided instructions; fast setup. I'm powering it with a 2A external USB "wall wart", and using an external / outdoor focused beam antenna, I have extended my wifi network across a 500' open space. Great value- will see how it holds up over time.