Ozgoe Happy Bell Mount Metal Plate with Sticky Adhesive Pad for Collapsible Grip & Stand/Magnetic Phone Car Mount/Magnet Cradle Holder,Black

I chose these for their low profile design, for several applications.The fact that the 3M adhesive backing is thin as well, is also a plus.However, I was shortchanged in the the product that was actually delivered. I only received a qty of 14/16 metal pieces. 6 small circles, 6 larger circles and 2 large rectangular metal pieces —1 that was damaged before being put in to the package to be shipped. It’s not a deal breaker, but everyone is entitled to receive paid product as advertised.Pros:Low profile metalLow profile 3M adhesive backingCons:-shortchanged 2 rectangular pieces-shortchanged 6 clear film for the small circles-Received some Damaged product(obviously not from shipping)Quality check was skipped on the large rectangular metal pieces. I received 2 out of 4 of them and 1 was bent from the manufacturer and scratched across the middle.

I purchased this to fix a problem my wife was having with a scrubber mop head not staying upright while it was drying. I first thought of velcro but haven't had a lot of luck in the past with velcro sticking all that well to certain surfaces. So I tried using these metal disks by sticking the disks to the mop head and putting a strip magnet on the handle. The magnet wasn't strong enough to attract the metal disk but worse the disk fell off after one trial. I let it cure for 24 hours after sticking it to the mop head so that wasn't the issue. I've since solved the problem by putting stronger magnets on the mop head and having them attract the handle, which is metal. Probably should have gone this way at first but I thought the handle was aluminum. Oh well...

This product worked perfectly for my purposes - mounting my collection of queen magnets on my desk. I have no metal in my office and needed a way to display my crown magnets. This product adhered perfectly to the wood of my desk hutches to hold my magnets. I'm very satisfied.

These metal plates are a great buy and are definitely worth what I paid for them The fact that you get 16 pieces of various sizes for this price is impressive. Build quality is good - the metal seems properly cut out and of high quality. The metal is very thin and is barely noticeable on the back of my case. The adhesive is 3M brand and seems to have stuck very well.The only problem I can foresee is the long-term durability of this metal showing scratches over time. I've had it on my phone about a week now and can already see some fine scratching (see picture). For the price it's not too big of a deal as I can just put a new one on when it's scratched up to the point that it's an eyesore.

Great variety pack, the adhesion on the back is great, only area of improvement would be the thickness of the plate isn’t as good as some of the higher end/more expensive plates. This makes the magnetization not as strong and the material more malleable. For the price, this is a great value and it gets the job done.

Exactly what it says it is. You get quite a few plates, and extra clear plastic stickers as a base (I Guess). You are supposed to stick the clear plastic stickers to the surface first. I am guessing this is for certain porous surfaces.So far I have use two of them. They contain enough ferrous material to hold to typical magnet mounts pretty well. So far they have not come unstuck, although the clear plastic stickers mentioned above are beginning to peel at the edges. its about 10 days in...

Great value. Round pieces fit inside or on top of Pop Sockets, work well on most other surfaces. Each plate comes with a pre-attached 3M pad you just peel and place the plate on the surface. I used these on my phone and GPS devices and they work fine. Edges can be almost sharp if you handle them roughly but plates sit almost completely flush with surface once attached. These are not reusable so once it's on it's there for good until you remove it completely.

Great plates includes the 1.18" small discs this size is hard to come buy. They worked great. They were small enough so that it stayed out of the middle back of my phones wireless charging area so am able to still use my wireless charger.