422866 Router Table Box / Finger Joint Jig 1/4" / 3/8" / 1/2" (422866)

Had a problem where the bars of 5 star restraining knobs did not fit into track. However, by using my feather board bolts from same track it worked perfectly (thank you other Amazon user that suggested it). Once everything in place. Off you go. Brilliant piece of kit. Very happy and easy to use.

Great results with this jig, straight out of the box. Works really well, good easy to understand instructions. Just make sure you do not use cheap router bits.

It's everything I expected it to be. Not sure how long the t-slot track will remain sturdy being mounted into MDF. For the price I would have expected it to have an aluminium base - but hey - I knew what I was buying. I see a question regarding will it fit on Lumberjack RS1500 - yes it will - though you need to borrow some parts off the front feather board that slot into the narrower t-track and all is then good and solid. Bit of a learning curve - of which i'm only part way through but initial cuts look promising. Deffo get an upcut spiral end bit for this - straight cut just tears everything out. So as it was a treat - I'm reasonably happy - but I could have made it myself for far less

I found this jig easy to use and my very first box joint was perfect. Only one stipulation , the manufacture should inform buyers that extended router bit may be required when using this product. Great service Amazon

This is an 'okay' product, but I suspect it's a very old model being shipped. Once set up it's fairly easy to use but the wood dust does build up in the tracks and needs constant monitoring. This is partly because my fence doesn't go back far enough and partly a design flaw.

I'm making a cabinet makers wall mounted tool chest, and needed this to join the corners, it worked wonderfully, Thanks

Great and easy, but it would be better if sold with the router bits as an extra where required.

Having tried building numerous DIY jigs from videos online I decided to treat myself and buy this item. After numerous attempts on scrap wood, it finally worked and produced a good result. My second attempt on different material involved more faffing about, but with patience, and lots of test cuts, it can produce tight joints. Had it been 20 % cheaper, I would have bought it months ago ...

Il prodotto si presenta fatto con ottimi materiali e ben progettato. Non ho avuto modo di provarlo in quanto non compatibile Infatti vanno fatte alcune considerazioni e controlli prima di acquistarlo: Il JIG si aggancia alla t-track del banco fresa, perché si agganci è necessaria una distanza minima di 12,5 cm tra il centro della fresa e il canale, è comunque possibile allungare la fresata di aggancio L’aggancio si effettua tramite spessori in metallo da inserire nella t-track; questi una volta tirati dalle manopole dovrebbero allargarsi e garantire la stabilità del supporto. Questi spessori hanno forma rettangolare con il lato in alto di 20 mm e spessore 9,3 mm quindi vanno bene per le t-track comuni larghe esternamente 30 mm. Altro problema è che gli spessori che fanno da riferimento per creare i denti dell’incastro sono in misure imperiali: 1/2, 1/4 e 3/8. Questo in se va bene salvo che bisogna avere le frese delle stesse dimensioni e queste in genere vengono vendute con codoli imperiali e quindi poi necessitano di mandrini (pinze) del router che riescono a lavorare con queste misure Insomma niente di impossibile ma prima di acquistare fate un passaggio per verificare tutti questi dettagli, se siete attrezzati potrebbe essere un buon acquisto

Excellent table router box joint jig. Easy setup and use.

Ware ist gut angekommen. Vielen Dank

il est bien fait, solide, par contre c'est pour des mesures en pouce et pas en mm. si vous avez pas les bonnes fraises c'est inutilisable

The unit it's self is great after setup, one's set make more than one box and make cheat blocks to aide in setup next time you use it.