Primefit CR1401G Replacement Air Regulator with steel-Protected Gauge, 1/4" Npt

Used to replace the regulator on a Craftsman air compressor. Easy to install and works correctly.

WORKS WELL AND EASY TO INSTALL

it's a great replacement for my BelAire air compressor with no leaks. *>Keep in mind, it's designed to let air out by the knob when you're reducing the pressure or turning it to zero. mine came set to zero, so i turned it to max(full +) when installing it, so I got no leaks by the knob and got tank pressure with it set to full, I'd suggest to turn it to full when installing it. I think the knob should be large enough for the average person imho. I used tru blu thread sealant and let it cure with no leaks from my conections, or the regulator itself, but it does release air by the knob if I reduce the pressure or set it to 0 which is normal. it's a great value and replacement so far, but time will tell if it lasts.

Worked perfectly just as dedcribed!!

Perfect low cost replacement regulator for my portable compressor. Works very well. Just installed, so time will tell about how long it will last. Just pay attention to the direction of flow which is indicated by an arrow cast into the side of the unit. Easy to adjust the pressure.

deWalt wanted $265 for this exact gauge. I got it on here for 12 bucks and it works just the same.

This works great on my compressor. It keeps the pressure as it should, and is easy to open and close (I turn the hose pressure to zero when I finish because there is always a leak on one of the connections for the hose and I don't like hearing it cycle needlessly at random times.) The hook up was easy since I already had the connections, and it fits just as the original equipment did. I would recommend to anyone who needed to fix theirs. Update after 3 months: It sucks. Failed. After three months it has started leaking around the adjustment knob, just as the one it was replacing did. I thought maybe I had not taped the threads well enough, but after disassembling the whole set up to include the pressure gauge, then the regulator, the putting it all back together, it is the adjustment knob. It failed. So I am off to Lowe's to get the Kobalt that I didn't want to buy, because I need it today to put up the trim we were redoing in the house. Guess you get what you pay for.

I bought this to reduce my 200 psi Viair on board air to 100 psi for my air offroad truck lockers. This also fixed a problem of my o-rings getting extruded out the Milton quick disconnects when airing my tires up. I guess the 200psi is too much for those. The problem is this is not very consistent. When it was cold in the morning, the regulator stuck on and blew out my air locker seal with 160psi when set at 90psi. Several months later, it now leaks continuously and needs replaced. Also, not very high flow so I only get 70psi when airing up tires (when set at 90psi). Not terrible, but could be better. I think it would be fine for a more controlled (indoor) environment.

The original replacement Regulator for my 20+ year old CH 4 Gallon compressor was discontinued, so I needed a substitute. Although this one is configured slightly differently, it installed well, it’s functional with the design of my compressor, and it works flawlessly. Please be mindful of two things: 1. air flow direction; There will be an arrow on the regulator, and an R or L. Sometimes they are interchangeable, as was the case with me. I replaced an R with an L, and it still worked with the layout. You’ll just have to look closely at the photos before you order, and decide if it will work for your application. You can see from my photos how the configuration differs from old(with red “CH” on the regulator knob), to the newly installed one. 2. The coupler that connects the regulator may need to be replaced, depending on its age; mine did. Do yourself a favour, and order one or two at the same time; I happened to have a couple in the tool box.

Sirve para un un compresor con tanque de 8 galones puesto que es el que uso. Es regulable, y mantiene la presión con forme se visualiza en el indicador.

Replaced a broken regulator on an air compressor. The gauge seems accurate when you blow up. Using the regulator may not be entirely accurate. You may have to set it and operate it once blowing air or whatever your needs are and checking to see if it maintains the set pressure. My air compressor is set for 135psi max and the old gauge made it seem like it was 150psi, this new gauge stops at 135psi when the compressor stops. So it seems accurate. Works for the basic needs of the shop and blowing some air here and there.

Funsiona muy bien

Fit great, functioned as intended!