Prime-Line M 6258 Frameless Shower Door Bottom Seal for 3/8 In. Thick Glass Doors – Stop Shower Leaks and Create a Water Barrier, 36 In., Clear Vinyl (Single Pack)

This shower sweep works really well for stopping water from leaking out of the shower. It fits securely, is easy to install, and helps keep the bathroom floor dry. Good quality and holds up over time.

I recently had a custom shower built. I love having a glass door on the shower I think it elevates the look of the shower. I purchased one but needed to ensure that it fit my doorway perfectly. This was a perfect fit because the shower door was measured well. The tile is completely flat and even. This was easy to install and I have no leakage from my shower. It is almost completely see through so matches the door. Forms the perfect seal for the shower door. It arrived fast and is offered at a great price.

Good product,, works as advertised... would recommend,,,

I fit great on the glass width and is very sturdy! My girl math made me not take into consideration the bottom part, so I did have to cut the entire bottom part off because my shower is raised a bit, so it wouldn't fully close. After I cut it a bunch of times with kitchen scissors, it worked! I did have to heat up a spoon to push the sturdy plastic down, so my door could close a bit better. If the company is reading these comments, can you please make one that doesn't have the bottom flaps that touches the floor and possibly the corner make it so the plastic is a bit more flexible. I love that it's SUPER sturdy but my door doesn't close all the way because it's sturdy and it angles out. But again, my fault because I'm not great at measuring. I've had it on for a couple of weeks now and no water is coming out.

Easy to trim to length with the right tools. Nice snug fit on our 1/4” shower door. Had to trim off the inner rubber seal so door would close fully. No big deal. Works well for the $$.

Glad I ordered it from Amazon. None of the local hardware stores had it. Was really easy to install. The water stays inside the shower. Great quality.

Shower door sweeps are one of the most common items that I replace for my clients. If you have a glass shower door, you can bet that the sweep will start failing at about the two-year mark. When this happens, water will start leaking out on your floor, this is frustrating and, in some cases, can cause damage to the sub floor. These seals are easy to install, all you need is a sharp razor blade, some glass cleaner and a little time (maybe 10 minutes). Make sure to measure the thickness of the door so you can order the correct size needed (unless you have some off brand, budget grade door that the builder installed because they wanted to save a penny or two, see the "heading title"). The old sweep should slip off the door, downwards. It may take a little force because of calcium build up but will come off. Using the "new" sharp razor, BE CAREFUL, and shave the calcium debris off the door, then clean the glass so the new seal will slip into place. Make sure to install the sweep with the water diverter facing into the shower enclosure. The seal should fit snugly, and it may take a little force to get it place. Start from the hinge side of the door and work towards the outside edge. Once installed, you can use the razor blade to trim the seal to length, and you're done.

perfect fit

Does the job!

Ordered this a few weeks ago and installed it the same day it arrived. I'm glad the item is longer than my door because it allowed me to test cut. Here are a few important tips I learned: 1. Test cut on one end. I didn't have a fine tooth blade on my mitre saw so I tried using a course blade and it chipped the one end off unevenly. Definitely use a fine tooth saw/blade. I ended up using a manual coping saw and it worked out great. 2. Sand down the corners so that once it's installed, the sharp plastic corners do not scratch anyone. It doesn't require a lot of effort for the sanding. I just picked up a small piece of sandpaper I had lying around and rounded the corners. 3. When applying it to the shower door, you will definitely have to apply a little bit of pressure to get it on but it's a nice snug fit on a 3/8 door. 4. Clean any gunk/mold from the old sweep prior to putting the new one on (important otherwise it won't go on properly). As another reviewer mentioned, it does turn white when you cut but this is because the wrong tool was used to cut it. Take your time when cutting it and again, use a fine tooth saw or blade. That's the only way you will get a nice finish on your cut.

Installed it on bottom of glass door and now provides a very good seal at bottom of glass shower door. No water leakages any more. Great quality product! Would buy again!!

Se coloca fácilmente y se ajusta de manera exacta en el cristal de la puerta y además impide eficazmente que el agua se filtre y salga el agua. Excelente producto !!!

Didnt work, seal was weak and bent (see picture) water still leaks, cant send it back as I had to cut into shape to make it fit. Not cool, thanks for wasting my time and money.