Aaron 4Pcs 50W 6ohm Load Resistors - Fix LED Bulb Fast Hyper Flash Turn Signal Blink Error Code (Resistors get very hot during working)

Got here super fast. Less than 24 hours and some of the least expensive ones I saw. Worked perfectly on my 2007 Jeep Grand Cherokee Laredo. I'd installed the "Yorkim 3157 Led Bulb Red Bright 3156" LED bulbs and the turn signals were hyperflashing, the bulbs were strobing/dim and I had no brake lights. The first one I installed didn't work, but it was just operator error. You need to give those connectors a really good squeeze to get them to connect. They do get up to around the same temperature as the halogen bulbs used to, so the fact that they're pretty compact helps a lot when you're mounting them to something metal inside the cavity the lens housing sits in. You definitely DO NOT want these in contact with plastic, worse, the wiring harness. Good idea to mount them first, then connect them. The first one I did wound up being a little awkward because I installed it too close to the socket and didn't give myself enough slack. End of the day though, I got exactly what I wanted. The brake lights/turn signals work, and they're eye-searingly bright (I ordered tinted lenses for the tail light lenses, so I wanted something that wouldn't show up too dim after I installed them)

These worked great. The instructions correctly said that these resistors get very hot while being used. I did not really want to drill holes into the body to mount them, so I did a test. I ran the turn signal for about 5 minutes, which is about as long as I would expect under normal use. Certainly, 4 way flashers could be much longer. The resistors did not get very hot during this test, so I simply bundled them in with the wiring. My vehicle has separate bulb filaments for brake and turn signals. A vehicle that has one filament for running lights, turn, and brake, would be continuous use and would get hotter. I am pleased with these. They worked well, are well built, and a reasonable price. They also come with the quick T-tap connector which makes installation a breeze.

Work great and great price

DO NOT MOUNT TO PLASTIC. These make your leds work and eliminate the hyperflash go away. Very simple to apply with the wire clamps. But they get hot. This isn't against the product because it's reducing electricity so it will get hot. Just make sure you mount it with self tappers to metal OR buy metal zip ties and you can mount them with those.

They work just right. Had to resolder one connection because a pet guy ripped a wire off. It just came off at the terminal. Just make sure to mount to metal and away from water although they may be waterproof

I bought these load resistors for my AUXITO Upgraded 7443 LED Bulbs Turn Signal Lights Amber Yellow found at https://a.co/d/8D4ANqF. They were for my 2016 Honda Civic Sedan and I saw an immediate improvement in the turn signal flash. They were SO easy to install and do get HOT, so they will need to be mounted on a piece of metal around your turn signals. The lengths of wire soldered into place are a little short and soft and WILL break if you move it too far. They included the wire tap-clamps, which work perfectly. I suggest you use some electric tape over the clamps to make sure they stay connected and protected.

I was frustrated when I bought a bunch of LED bulbs to replace my older turn signal bulbs and got the "hyper flashing". So I bought these and they resolved the hyperflashing issue. These are not particularly hard to install. The two hardest things to figure out with these: 1. Which electrical wires to splice these into (each car is different). I finally was able to figure it out by comparing the wiring colors for the turn signals on each side. Both have a black wire and then the turn signal wire is usually different on each side. I highly recommend that when you put the splices they include onto both wires, to then use pliers to push the metal tab into the wires first, and then close the snap lock piece over that once the splice is completed. 2. The purpose of these is to put more resistance into the wiring to prevent the car from thinking the low voltage use is because the bulb is out. So that gold colored resistor does that job, but as a result, can get pretty hot (like 250˚). So it really helps to mount the resistor to something metallic so it can dissipate heat better. I've seen some YouTube videos where some people mount them to a sheet of aluminum or other metal and then mount that whole assembly to plastic if they have no other option. Bottom line--these things work, and aren't really too hard to install. First one took me about 15-20 minutes to figure out. 2nd one took less than 7 minutes. I have two more to go and figure they won't take long at all either!

Did not fix my hyper flash.

As described, works well

Likes: - Resistors have a large heatsink but are still compact enough to install in tight spaces - The wire gauge and the insulation on the resistors are thick and durable - The wire clamps that were included worked great in making contact with the wires on my OEM turn signal harness - The resistors are non polarized so they work when installed in either orientation - I touched them while they were on and they did not get as hot as the warning message claims - They eliminated the hyper flash on both my front and rear LED turn signals back to normal flash speeds Dislikes: - Initially when I first installed one resistor on my rear turn signal harness the hyper flash still existed, so I wired a second resistor in parallel with the first one and that did the trick and the hyper flash went away. FYI, I did not need to install a resistor on the front turn signal due to space constraints behind my front bumper, to summarize I used two resistors on each turn signal in the rear of the vehicle - The wire leads coming from the resistor are a bit short, I would have preferred them to be a few inches longer - No self tapping screws were provided inside the package so I used Gorilla Mounting tape to stick the heatsinks to the bare metal on my rear bumper frame, this is not ideal but since the resistors didn't get very hot I am not concerned about them melting the adhesive tape Update - Sept. 17, 2025: Resistors are working perfectly fine since installing them last year. They have survived one winter so far and haven't skipped a beat. I would definitely recommend this if you're planning on upgrading to LED turn signals and can wire them yourself.

Excelente producto y de buena calidad, super fácil de instalar buen producto. ! ! ! Lo recomiendo mucho este tipo de resistencia. ! !

تعمل بشكل جيد منذ سنتين

C est parrrrrrfait!!!!!