LOVIMAG Copper Foil Tape (2inch X 33 FT)

I used this copper foil tape while rebuilding a 2005 Fender Highway One Telecaster that I recently brought back to life. Before installing new electronics (pots, switch, and a set of Fender Texas Special pickups), I wanted proper shielding — and this tape worked flawlessly. What I liked: The adhesive is truly conductive Sticks extremely well to wood cavities Easy to cut, shape, and layer Soldering to it is clean and reliable Provides excellent EMI shielding for single-coil pickups My old relic’d Tele is now quiet, tight, and professionally shielded. Great product — absolutely worth it for any guitar restoration or upgrade.

This tape works well. It is thinner than I thought it would be so you have to be careful peeling the backing off of a long piece because it will want to curl up and once it sticks to itself, it is not coming up. I will purchase this again.

There is nothing I can think of negative to say about this product. I use it to shield electrical interference of the guitars I build, and its so easy and slick, you'd think new ones would have it installed from the factories, but you know, if they can save a dime on each guitar they build, they will even if it means you get something inferior in its place, but they take their cue from the car manufactures and tell you how great they build everything when in fact they are built as cheaply as possible. But use gloves, it is capable of producing horrendous tiny cuts that you don't notice until you use hand sanitizer and after you are done screaming in pain long enough to look, you find twenty tiny cuts on your fingers... But it is so easy to use, rip a chunk off and stuff it into a pickup cavity and just push it into the bottom and sides, missed a spot, tear off a chunks twice the size and toss it in there and push it to form around the corners. There is no need to worry about continuity, the adhesive works like it should, it is easy to just use anything rounded to press it in place and smooth it out, it looks pretty cool when you are done, run a strip to contact the back of the pickguard and that should be covered almost to the edges, this effectively gives the pots the ground they need, no need to run so many ground wires, and on top of it all, you can easily solder wires to it wherever you need them. It is a great product and I can't recommend it more than I already do, but damn, remember to wear gloves.

Versatile and Reliable Copper Foil Tape I used this copper foil tape for EMI shielding in my guitar and was impressed by its performance. The tape is easy to apply, with a conductive adhesive that ensures a solid connection. It's flexible and can be shaped to fit various cavities, making it ideal for electronics and crafts. The adhesive holds well without leaving residue, and the tape's durability ensures long-lasting results. The appearance of this tape is copper, it works really well and has a good visual appearance to it.

This stuff is flexible and it will stick. The adhesive is good and can be somewhat fragile. The stickiness can be difficult if you have to get into tight spaces. I had recently copper shielded my Leo jaymz LP that needed it. The internal pockets looks so much better afterwards and interference is lower. Tested this after turning off my noise gate. I have alot left over and will be shielding all of my guitars until its gone

This material is the top of the line, elite... THE REAL DEAL.. HIGHLY RECOMMENDED...! A MUST HAVE !

We were at our wits end trying to find a humane solution to the snails which had suddenly decided that our lilies were their favorite food. Then we read online that they hate copper and will not cross it as it gives a mild shock to their system. For just a few dollars this was an unexpected success. We placed the copper tape on the wall around the plants and, so far, no more night snacks for the snails.

Great for guitar shielding. Sticks well to clean surfaces. I like the “thickness”, thin enough to flex into tighter tight corners. You have to be cautious tho, it does tear fairly easily

It has great adhesion and the sticky side is conductive so there is no need to solder the individual strips together if they touch. Used it to shield a guitar, but you may want to get the 1 inch wide for that job since I had to cut strips out of the 3 inch one to fit the cavities. I highly recommend it to get rid of the dreaded 60 cycle hum.

strong and double side, works fine

Has conductive adhesive. Works well.

If possible, adhesive quality should be improved. otherwise overall quality is decent.

… to tame unwanted RMI/EFI for a Jazz parts bass.