Question 1

Can this product be bent to fit curved nosurfaces after it is moulded in a silicone mold?

Accepted Answer

Yes, the material is very playable and would comply with a silicone mold. If your plan is to place a ball into a mold and press the material into shape of the mold and allow for excess material to flow through a gate that would work.

However if your plan to to place small amounts of material at incremental times it might be a challenge since the material was designed to adhere to wood not silicone.

In some cases I have used 0.02" aluminum sheet as a form and pressed the material into a void with the aluminum used as a material stop.

Once the material has dried I have separated the aluminum from the material.

For texture after the material has stated to set have pressed a rough sawn wood sample into the material to leave a texture,

In "some" cases once you pull even amounts of Part's A and B and mix the material is sometimes sticky.

The "stickiness" can be decreased prior to application if you allow it to air dry "temperature dependent" for a few 5-10 minutes - again "temperature dependent" (higher the ambient temperature the faster the material sets).

So yes the material can be molded using a silicone mold.

Hope this is of assistance!

All the Best,

Question 2

how to store the products?

Accepted Answer

I don't do anything special.  Just leave them in their original covered containers, stored at room temperature.  I have some left over purchased in 2015 and some newer from 2017.  I just used some of the 2015 product last week and it was in good condition--the  pinkish material seemed slightly stiffer than when it was fresh; but when I mixed it together with the white it was completely soft, pliable and moldable and hardened just fine.  Hope this answers your question.

Question 3

can i use this product to fix wood siding?  the wood siding on our house has cracks and I would like to fill the cracks with this product.

Accepted Answer

I found that it was the BEST product to fill in areas on my siding.  I tried Bondo but it is so sticky and set up too quickly.  This stuff is my favorite.  I picked out small areas of dry rot then applied wood hardener.  I came back later and used this SculpWood and it worked perfectly.  It dries hard as rock. I am about to have my house painted, the contractor was impressed by my efforts (I am a 65 yr. old female with no experience)....He said that he will place some sealant over it to make sure that it does not show cracks later on.

Question 4

Once cured, do you need to use a primer before you paint it??

Accepted Answer

Primer is not necessary for adhesion, but generally makes covering color easier.  Primer will make your item a  uniform color before you add your chosen  color of paint, so the pinkish color of the system 3 will not stand out.  If you don't use primer the System 3 may require more than 1 coat of paint to create a uniform finished color so the repair doesn't stand out from the rest of the finish coat of paint.

ASIN	B0015YPIZW
Best Sellers Rank	906,891 in DIY & Tools ( See Top 100 in DIY & Tools ) 1,662 in Wood Fill
Brand	System Three
Colour	Clear
Compatible Material	Wood
Container Type	Pail
Customer Reviews	4.7 4.7 out of 5 stars (1,075)
Global Trade Identification Number	00646697903011
Included Components	System Three 1-Quart SculpWood Moldable Epoxy Putty, 90301
Item Form	Putty
Item Package Quantity	1
Item Volume	1 Quarts
Item Weight	454 g
Manufacturer	System Three Resins, Inc.
Manufacturer Part Number	1600K16
Material	Epoxy Resin
Model Number	90301
Number of Packs	1
Number of Pieces	1
Other Special Features of the Product	Strong
UPC	646697903011
Unit Count	946.0 millilitre
Viscosity Level	High
Water Resistance Level	Waterproof

System Three 1-Quart SculpWood Moldable Epoxy Putty, 90301

Details

Details

Description

Specifications

Common Questions