ECOTRIC Hitch Cargo Carrier with Ramp Foldable Hitch Mount Wheelchair Carrier Mobility Scooter Ramp 500 lbs Weight Capacity

Anyone looking at this item be very very aware that this is definitely a two man lift and a 3 man to fit itAnd it’s taken me nearly a month to have it collectedBuyer be aware

I bought one of these last year 2023 for a really good price from Amazon. It’s a tad heavy but super strong the ramp is a good weight and folds vertical or flat depending on what you are carrying, big tick!I have a mobility scooter which goes on quite easily but just wish it was made to be 120cm in length. Also I found it a little low to the ground when on a gradient, however I overcame this by buying an offset 2 inch receiver adapter which raises the whole thing approximately 6 inch higher. Don’t know why we don’t see more of these as they are a lot easier to store than a trailer plus it overcomes the tip bylaws of no trailers.W Broadley. Blackpool.

Thanks for the great craftsmanship!

I have not put it together yet but in box it is very heavy. My son is guessing 60 lbs. I would say 60-100. I found another like it same price but receiver part was steel but rest was aluminum. This 1 is all steel. In reviews 1 guy said he had to weld a peace to make it work on his Trk. Well U can't weld Aluminum to steel so I got this 1. Also if it should crack or need repair U can weld. I got it to take snow blower over to my sons when needed and hall my red trailer on with grass for garden. This will be much easier than the bigger trailer. OK I put it together and on the trk. It is very well built but instructions need some help. It tells what bolts go where and the pins. I took it apart 2 times and put it together 3 times. 1rst I put the Tung on wrong. U want the ramp to drop on passenger side so pay attention to hinges. Only 1 of 2 ways to do it I did it wrong. Than there is 2 bolts. 1 long and 1 short. Long 1 goes through tung and piece that goes into trk hitch. Short 1 goes into threaded hole under it to level. On tung there is a small piece of steel welded on bottom of tung for added strenght. It was used but not needed. There is a pin with S pin for it. So with long bolt and pin there is no leveling. Maybe to lock it? Well I did that wrong also. 3rd times a charm. The piece to pin the ramp up and down I had to put about 6 washers to move it out cause ramp was 2 close to frame. I got the ramp at a 90 degree pin to line up but 1 that pins it down to platform I need to drill out bigger for adjustment for lower pin to lock ramp in a not in use mode. Also none of it is not standard. Most metric and some don't know. Ended up using 2 crescent wrenches. It is heavy. I took out of box in house read instructions and took out in pieces in morning. It took me all day to assemble and on trk so still need to drill hole out. Now I could put together in couple hrs. I would buy it again but see no need to. It will do what I want to. I also went back to amazon's add and took some picks with phone so I could enlarge and see better. There is a small bag with blk nuts and washers. Put in pocket. I didn't see and wind blew away along with instructions. Found latter when done. Also peace that goes into trk hitch has a added piece welded on for wear. The tung should set down from top. LOL I hope this will help U do it in 2 hrs and not all day. Also the reflectors are very small. I got 2" X 50' here on amazon will put bigger and more than what they sent. Only thing is that my trk sets high but I can pull up on street and drop past the curb gaining 4-6" on ground height. Good luck.

Le trou n’est pas percé a la bonne place la rampe ne peux pas pas être barré en position fermer . La rampe vien déjà visser a la base , ils aurais pu facilement voir que c’était pas aligné en usine.

EASY fitted. Easy to use, both putting down & putting up. The ramp is easy to put down & up.My only problem is exiting & entering driveway ... big dip ! & it drags on the tarmac. I have to place boards in the gutter to get clearance ... That is not the carriers fault at all, So I ground a half inch off the bottom of the rail, well maybe only quarter inch ! I like it a lot.

Absolute garbage. Who built this? An 11 year old Cambodian kid? Absolutely not rated for 500lbs not even close. The manufacturer shipping weight of my wheelchair is 360lbs. First day using it the steel fractured and bent 3 miles down the road. Who ever designed this doesn’t know a thing about welding or metal work and definitely didn’t stress test this because no way it hell is this rated for 500lbs.