ALadrs Resin 3D Printer Flex Building Plate,6.61x3.54inch Spring Steel Flexible Plate and Magnetic Base Platform for Phrozen Sonic Mini 8K/8KS LCD Resin 3D Printe 168x90mm 2pcs

I have two of these for my one for my Crealty Halot Mage 8K and one for my Crealty Halot Mage 14K. Works very well with good adhesion. However you need to be aware that if you just stick it on and use it you may break the printers screen. The only way I found to fit it was to remove the plates and grind out an additional 3mm of movement for each of the adjusting screw slots before releveling. So this may not be for everyone.

Ok so being a complete newbie to 3d printing and trying everything to stop my print fails seen alot of people using wham bams then seen these alot cheaper but they work just make sure to clean your build plate i used 1600 grit wet and dry then isp to clean it down line it on to plate then using clamps compressed it onto the plate and left it overnight perfect prints again woo hoo im not doing it wrong (yet)

This is a must have upgrade for any elegoo jupiter 6k. Saves on leveling and having to take the platform out after every print.

These are pretty thick sheets of metal compared to other flex plate I have used. Measuring approx. 0.6mm makes it hard to flex particularly when printing smaller items near the edges. As I print pretty small pieces I find myself struggling to bend the plate to get the prints off and end up using a scraper anyway. If printing large items this is less of an issue as there is enough of a bend to pop those off. The company was helpful and processed my return quickly. Also worth noting, you'll want to use 80-120grit sandpaper on the surface to ensure your prints get good adhesion (they come as brushed steel but too smooth for a good grip). This is a standard across all plates. My other plates measure approx. 0.3mm and they are actually flexible and a dream to use, unfortunately I still have not found a suitably thin plate for my Anycubic photon M3 that is the correct size (Bummer). Once benefit of having the 0.6mm thick plate is the magnetism is strong. again only a benefit to those printing large heavy items.

Much better than standard

needs a spacer for the mono 4k - which doesn't seem to exist, so you will have to make\design and print yourself - with one of your other printers as this one is out of action if you followed the instructions. Or save yourself the hassle and buy a plate from a different manufacturer just don't buy it - complete waste of time trying to get it to print, better off just throwing it and a bottle of resin straight in the bin

So much easier than relying on build plate

Bought for the Saturn 4 Ultra, they do not work on the Saturn 4. The quality of the product is great and it does do what it is expected to as far as a flex plate goes. But it does not work with the detection software of the Saturn 4.

Very easy to install on Saturn 3 ultra, works perfectly. You may have to increase bottom exposure a little

This item works better than expected. The magnetic backer is incredibly strong and the flexible stainless plate makes model removal incredibly easy. I’m so glad I found this product!

Habe die Platte beim Saturn S dran und es klappt super damit zu drucken Habe bei ca. 50 Drucken nun keinen vorzeitig abgelösten druck . Lässt sich leicht abnehmen und danach den druck ablösen . beim anbringen muss man aber aufpassen das man die Finger nicht einklemmt denn die Magnete haben richtig Schmackes

Got these plates for easy removal of my prints, and they work! At first there was issues with prints failing on one side. But I realized later it was uneven. Did a few adjustments and now all prints are coming out great.

Redoutable d'efficacité, à voir à l'usage, sinon, bonne accroche, décollage impeccable, si elle est collée proprement ,le support doit être hyper propre,elle tiens super bien dans le temps 😁