EZDIY-FAB PCIe 5.1 Adapter - 600W 12+4pin, 16pin 12VHPWR GPU Power Connector, 12V-2x6 GPU Adapter,180 Degree Right Angle - Compatible with RTX 3090Ti, 4070Ti, 4080, 4090 GPU - RVS Type, Black, 1 Pack

This 180° adapter is a perfect component for cable management in your builds and is a good value for the money. Functions perfectly well for my 4090, solid connection on the power port, and it's best suited, in my opinion, for vertically mounted GPUs since it hides the power cable out of sight give a cleaner look. I didn't notice any overheating on the connector either so it's safe and will not "melt" your GPU. Overall, I highly recommended this connector for that cleaner look in your PC builds!

I chanced these with my 4090 to reduce cable clutter in my case and have had no issues at all so far. I was worried about risking such an expensive component with an adapter of this price so I gave it time before reviewing in case something happened but so far so good! My expectations for an adapter of this price have been exceeded so I have no complaints I can make. It fits my GPU extremely well, has a nice design, doesn't seem to get hot, and I have noticed no changes in performance from my card. I did undervolt before purchasing this so it's possible that full voltage might be a different experience but I would not expect that to be the case.

This little adapter is made of aluminum and feels solidly built. Installation is straightforward. The angular shape and white housing look perfect for my PC. Functionally it's pretty simple, all it does is reroute your graphics card power cable backwards over the top of the card. It's pricey for what it is but you know what you're getting, a little aesthetic accessory.

Feels sturdy and expensive, although it’s bulkier than I expected. I wanted something like this so I didn’t have to flex my 12VHPWR cable 180 degrees, and also have it touching my AIO tubes. This resolved that. This item is both functional and aesthetic!

Works as intended, although the connector itself gets super hot with an rtx 4080 overclocked. I probably wouldn't use this with any more than 350 watts. AKA 5080, 4090, 5090=Possible melting.

The EZDIY-FAB PCIe 5.1 Adapter is an excellent product and worked perfectly for my setup. Besides delivering solid, reliable power through the 600W 12+4pin (12V-2x6) connector, it also adds a very cool visual effect to my graphics card. I have an ARGB case with a transparent orgmirror side panel, and this adapter really stands out - the lighting and design make my whole build look even more impressive. Functionally great, visually awesome. Highly recommended if you want both performance and a stylish upgrade for your GPU.

*After finally getting this delivered after a 2 day delay I was very Skeptical of installing this on my brand new Asus Tuf RTX 4090 OC. *I spent hours of research looking into the 12VHPWR failures, Cable/Mod's recall, reddit posts, and watching GamersNexus coverage and testing of the failures. *I finally gained the courage to install this hefty lil 180 adapter knowing what to watch for. *First thing I noticed when connecting the native PSU 12VHPWR cable in is the tight fit of the connector which is a very very good thing, pins inside are making complete contact and cannot be tilted to one side. "Some connectors where loose and could tilt causing the pins to misalign and create incorrect impedance which would lead to pins heating up on the connector leading to failure." *Connecting it to the GPU is just as tight and clicks into place, nice and flush. *After getting it installed I turned on my system and left it idle for about 10 minutes watching the adapter closely and using my Electronics IR thermometer to periodically check idle temps and averages 35c on both connections. Good so far. *I then stress tested my GPU using Metro Exodus Enhanced Edition benchmark and Unigine Superposition maxed out 4k. The temps I seen on GPU Connector 47c- 50c and the PSU connector 48c - 52c and the heatsink 46c. *When compared to IR thermal imaging that GN Steve has conducted, his results where average of 65c on a good cable. *So in conclusion this 180 adapter is actually good. Time will tell and I will update if that changes, if I don't update, that means it's still kickin.

Warning: Using this adapter can cause an unbalanced current and may cause your 12VHPWR connector to burn. At first, I thought the adapter connection was loose, but after multiple attempts at replugging and pushing it in (which was a pain), the same pin still showed a problem. I tested the system without the adapter, and everything ran normally. Luckily, my Astral 5090 is equipped with power-pin detection and it was screamming. I think mine could be a manufacture defect but to have such quality control that could potentially burn your gpu is a big red flag. So, use this adapter at your own risk.

O produto deixou meu setup mais limpo, e como há proteções no conector PCIe5, fico mais tranquilo para trabalhar e jogar. Obrigado, Amazon e EZDIY-FAB.

I can confirm that the RVS is working with the MSI RTX 4070 Super Gaming X Slim.

MSI GeForce RTX 5070 12G GAMING TRIO OCに使用。 バックパネルやその他部に当たる事無く使用出来ております。 （バックパネルより数ミリ浮いてしまいますので気になる方はシリコンパッドかなんか挟んどけ） 個人的には焼損報告の多いこのコネクタ規格の物にアダプターなど言語道断派ですが、 250w位だったら大丈夫やろそんな神経質にならんでも。 と思っております。 差し込み具合はガタやグラつき無く、少し強めに押し込まなくてはいけない程度の感触。 作りは悪くない、いや良い。

Facil instalacion nada complicado, se lo puse a una RTX 4070 Ti sin ningun problema, recomendado para gabinetes que cuentan con poco espacio, ideal para ocultar los cables y para que se vean bien esteticamente. Ojo con checar como viene la entrada de tu grafica, ya que la entrada puede venir al reves, tienen muchas gamas de colores lo que le da un plus. recomendado.

Product causes PC to black screen and ramp fans