ALECPEA Silicone Glue, 30g Clear Flexible Adhesive With 3 Droppers | Waterproof, Low-Odor Bond For Silicone Crafts, Kitchen Accessories, Electronics And Mold Repairs

Got it for securing silicone cord knots when making bead bracelets, and it sure works! Just be careful, it behaves like superglue so don't get it on you. I did, nailpolish remover got it off though.

Works just as advertised, had to glue a resin item onto an apple silicone iPhone case. Worked perfectly, very happy

I used this glue on a medical silicone item. It bonded very strongly, water tight and bends with the material without further tearing. The nozzles make it easy to use and really get into those small places It’s very runny which is useful for small repairs because thick glue can get very messy and look unappealing once dried. However, the nozzle clogs up very fast within seconds of dispensing the glue. Some of the glue is wasted for this reason. It doesn’t dry clear and forms a crust once dried making that area feel rougher. Value for money is good. Can be used for a lot of applications. Comes with multiple nozzles so you can swap them out if the glue dries inside.

Great for sticking silicone but a little goes a long way

Works really well although definitely wear glasses accidentally squirted in my eye had to go to hospital😳😎

It did exactly what it said on the little bottle.

👍

Leaves a horrible residue on the squishy, goes crispy upon finish, not what you expect with a silicone specific glue. Starts smoking and burning when touches paper towels.

Finally silicone glue that actually works!

This is 100% silicone glue, it’s not extremely flexible but it is slightly flexible without cracking. The most important part is you have to clean your surfaces, wipe clean and rinse with isopropyl alcohol and allow it to dry. Roughing the surface would be even better for adhesion. clamp your things together to let it set up. That 10-45 seconds isn’t a joke. Allowing it to cure for the full 24 hours before use. It’s got a slight odor, different than plan CA glue which is what also leads me to believe it isn’t plain superglue. It’s super thin, and will bead up and run off of your silicone items, but so far I’ve managed to glue several pieces of silicone mat together and they hold well. It leaves a slight residue around your glue surfaces but so far I have no complaints about its ability to glue silicone together. We shall see if it’s better or worse than sil-poxy but it’s certainly significantly cheaper.

How can there be any negative reviews about this product. I took 2 1/8 silicone hoses and cut it into 4 different section. I used the included reduction fitting and just put enough around the edges on just one tube- instead of holding for 5-10 seconds-( having previous experience with a rubber glue called KISS- which at the time years ago was the only superglue that was flexible for both rubber and silicone) I held each section with enough pressure to not cave the tube, for 30-40 seconds. Then I went to a 1/4 silicone tube and cut them into 4 sections. I waited a full 24 hours instead an hour or so to set and cure. I now had 4 tubes that were glued using this product. I pulled and stretched it to more than double its length- the silicone tubes were not only glued (fixed) together, the tubing retained its flexibility-with just a little bit of material on the edges-that were a little hard. Most importantly the flow of any type of material- within reason- there was no blockage and then I pulled with real force. The silicone started to tear at the seam but it held and I could observe the flexibility of the product. It tore a little but held and their was no leakage. This product is beyond my comprehension. I didn’t know it even existed. I took the 3 leading silicone superglues on the market and this one outperformed by a wide margin. I did not try to see if it was ready in an hour 2 - I waited 24 hours. Incidentally the tubes looked like they had been welded together. A perfect even symmetrical joint. This the very best product I have used to date. It’s difficult to believe advertising because so much is that if music was advertising- they sing a fine tune. I know this is the real deal and know if you follow my procedure their is no chance of failure. I might add that I did not- did not - use isopropyl alcohol to clean the joints to clean the joints. Just a microfiber towel to wipe the cut ends before joining. I might also add when cutting the silicone tubing into sections. I used an internal metal rod to make as clean of a straight cut as l could. They weren’t perfect. It didn’t matter. 2 days ago I wrote this review and tried another test. I had some old silicone ear tips that I occasionally wear. I made the best cut I could on the stem and it was not straight. It was jagged and out of round. It didn’t matter the product welded the stems together as long as their was enough pressure where the silicone from both ends were crushed( if crushed is the right word) I did not clean the stems in any way, did wash my hands. In closing, this silicone superglue is fantastic. The real deal. I am elated that technology and chemistry have evolved to make this product available and that it actually works better I think than advertised and as good as advertised. It does require some practice and a little finesse to go along with it. Try some discarded material first once it meets your expectations- just do it

It works great..better than the stuff the manufacturer gives you in a tube. Makes you a pro repairing with little effort. Just trim the edges where it bonds if you put too much by mistake.

Perfect silicone glue. Good for toys, spray nozzles, everything!