Crucial Pro DDR5 RAM 96GB Kit (2x48GB) 5600MHz, Intel XMP 3.0, Computer Memory (PC) - CP2K48G56C46U5

This for the Crucial Pro 5600 96GB Kit (2 x 48GB)The modules are Micron B Die DDR5I didnt fancy paying £380 for a 7200 Kit so took my chanceswith these hoping for around 6000 on an overclockThey worked out slightly better than i was expectingThey perform best if you dont go crazy overvolting them1.20V seems to be the sweet spot i wouldnt bother over 1.25VOn my Z790 Aorus Pro X these are totally stable at6400 with the ram voltage bumped from 1.1v to only 1.2vI can boot them at 6600 but they failed Karhu Memory Testerso didnt waste much time further trying 6600See image for fully stability tested tweaked advanced timings

Quality of this item was perfect. It has been reliable for the past year. Value for money is justified, the read/write speeds is quite high too. It is very easy to install onto the motherboard assuming yours is an am5 motherboard.

Really happy with the kit for the price, no issues with setup or recognition in bios, well packaged- there's little more to say!!Got this for a tenner less than the 36gb kit with ARGB that I had before but was at a lower speed, so happy with my choice- I'll sell the 36gb kit on and I have MOOOOOORE giggybytes than I started off with

It works well with no issues unlike my dominator ram so pleased

Had no issues with it, works just fine and is pretty fast too.

I upgraded from my Corsair Vengence 2x16 GB DRR5 RAM sticks to these, and after installation the Operating System was not booting, even though my PC was powering up. I even tried all the slots and ram combinations, yet still nothing. My pc seems to be only responding to my previous RAM installation, so after some searching online, I thought that I had a defective product. However when I got a replacement, the same thing was happening.It turns out that the RAM is not defective, it's just the BIOS settings needed to be reset back to their factory defaults. Which is kind of a nuisance, and not such a user friendly experience.If you encounter the same problem as me, be sure that is not the RAM sticks at fault, so here is what you are going to do:1) Consult your motherboard manual and find the JBALT pins to reset your CMOS.2) Power Off and remove any cables into your PC, including the power cable and the power switch that it comes with your PSU3) For 30-seconds, hit the Power Button down, from your front panel, where you normally power on and off your PC, to make sure there is no remaining power inside (I don't know if that is a valid requirement, that's what others advised me to do online, but better be safe)4) Get a Screwdriver (Or if you have a jumper cable, because that is the recommended device to use for this instance, but i didn't have one) and make sure it makes contact with your JBALT pins and hold it for 5-10 seconds (for reference, I have an MSI B650-P WIFI motherboard, and it is located at the bottom right side of it, where there are a row of pins) so it will discharge.5) Connect everything back together and try booting your PC back againAfter all that, you will be greeted with a fresh bios boot window and you can access your OS again, without losing any files or data.Afterwards I checked Task Manager and it recognised my 2x24GB DDR5 Crucial Pro Ram sticks at 5200Mhz, so I need to enable XMP profile and manually adjust the speed to 5600 Mhz, to get the advertised maximum speeds.Overall, these RAM sticks will be perfect for my needs, for working with intense compuational tasks for my work, projects, and gaming on the side, and the price for them seems fair for what they promise.

Ordered these for the Asus Maximus HERO Z690 system, The Crucial page shows it's supported, however, when installed, the system wouldn't post, and showed error code 53 on the motherboard which is for a memory error. Tried all slots in 1 or 2 module configurations and it kept showing the same error. I have two other kits on me and both work fine, so either this kit is incompatible after all or dead on arrival. Some research found out the DDR5 can be hit and miss, to be on the safe side, make sure it's on the motherboard's QVL list or don't bother as the memory manufacturer page doesn't show the real compatibility, it's just based on the theoretical spec sheet.Updated.My fault initially, Asus had released a BIOS update with added DDR5 module support on 22.03.2024, didn't realise there was such a recent update, and after installing it, the motherboard recognized the kits and worked great with it.So for anyone looking to upgrade, make sure your motherboard has the latest BIOS before installing this kit. For Crucial, would be nice if they added this on their product page, a note that their kit might not be compatible with earlier DDR5 boards out of the box and a BIOS update might be needed for it to run.

nothing negative, they feel quality and sleek with the all matt black theme. super nice speeds can definitely notice difference when using CAD and some games. 100% recommend if you use chrome ;)