CREWORKS Ultrasound Cleaner with Heater and Timer, 1.6 gal Digital Sonic Cleaning Machine, 180W 6L Stainless Steel Jewelry Cleaner for Professional Tool Glasses Watch Retainer Denture Parts Cleaning

The media could not be loaded. This thing is great! WHERE HAS THIS BEEN MY WHOLE LIFE?!Here is me using this with hot water and dish soap to clean my two year olds toys (which it works great for by the way). You can run batches of toys through this which has greatly helped my wife’s sanity as well as my own. Keeps all his stuff clean, just be careful not to put anything too delicate in because there were certain toys you could tell it started to take paint off. Tough to show in the video, but you literally watch the dirt and crap come off which is incredibly satisfying. Just rinse them off and leave out to dry and your good to go.Anyways!I am always working on cars, motorcycles, and anything else I feel I have a reason to disassemble. I was tired of having to clean things by hand especially intricate stuff. I have to say this works a treat.If any of you poor souls reading this have ever had to clean a carburetor, this is for you. This is big enough I can fit my whole rack of four carbs from my 1980 Yamaha xs1100 in it. Which is absurdly fantastic. I’ve used it to clean many items like firearms, intakes, dirty or rusted hardware, car bracketry. Basically whatever I didn’t want to clean myself. AND it does it while you go figure out what to do next. It’s amazing.Pro tips:Make little brackets that hold the basket up and keep the feet OFF OF THE BOTTOM. Ultrasonic cleaners (especially ones that use cheaper transducers, the things that make the ultrasonic waves) don’t like when things are placed on the bottom of the pan. The transducers will eventually vibrate themselves off the bottom of the pan.Fill the tank with water. “Degas” it when it has new water by running it for 15 minutes with nothing in it.Fill small containers with cleaners and put parts in those, AND THEN put those containers in the ultrasonic which is filled with water. This way you don’t use as much cleaner and saves you money.Gasoline works great on grimed up hardware and pretty much anything else due to the detergents in it. It’s also very cheap. Be careful that what you put in it doesn’t have seals that may swell. Or any other cleaner for that matter.Make sure the level of water is between the taper in the tub (the tub has a part near the top where it lofts outward a bit). Keeping enough liquid in the machine will allow the machine to work better and more importantly, last longer. If it also has TOO MUCH it won’t work as effectively.If your time is valuable like mine, don’t bother using the heater to heat the water up. Put some water in a pot and get it hot on the stove and pour it into the tub. It’s way faster, and this way the heating feature on the machine can maintain the heat and won’t overwork the heating element either.The effects of evaporust are catalyzed in an ultrasonic. It works very well and works very fast.Don’t expect miracles and for the machine to clean off an 1/8” of grime and crud from items. Scrape a bulk of the trash off then toss it in and it will do the rest. This will still save you time, money, and your sanity.It is amazing how clean it makes stuff. As someone who prefers to make old shit into new shit, it’s a life saver.I hope this helps someone!

This is a huge ultrasonic cleaner!✅ What I Like:The cleaning chamber is huge and makes it so much easier to properly clean my larger prints.It comes with a basket for smaller parts.Did I mention the size? If you have a build plate full of minis, then this is for you!This has a handy drain spigot, which is wonderful when it's time to swap out the fluid.⚠️ What Could Be Better:It's loud! Like, VERY loud! If you are unfamiliar with ultrasonic cleaners, this may come as a shock. I can hear this from another room with the door closed if I'm close enough.💬 Summary:I recommend ultrasonic cleaners for anyone who prints with resin. The difference between a print that has been cleaned by a traditional IPA soak and wash, and this is extraordinary.DO NOT USE IPA IN AN ULTRASONIC CLEANER!!! IPA is highly flammable, and this is a unit that has a heating element and uses vibrations to clean, which generates additional heat. I highly recommend Simple Green as it cleans just as well, is less dangerous, and smells MUCH better. For those starting out, a smaller unit would be best, but if you have large batches or just large prints in general, this is a must-have.💡 Final Thoughts:Would I buy it again? YesWould I recommend it to others? Yes

Well made..works great

Awesome!! I was nervous because i had all of these ideas of what these things could do and never actually seen them in real life. Sounds kinda silly reading that back. Lol. Doesn't matter because it exceeded my expectations. Ive been using for all sorts of things. It's great for things that have tiny cracks or crevices that you can't get with a brush or a pick. Worked great removing rust from a bunch of old tools and the other cool thing is that it makes cleaning the flux pcb's a hundred times easier. I'm real happy with this purchase and id definitely recommend this product. The quality is great..Cheers to the seller!!

Works great. I wanted to try one for cleaning carburetors. It worked above and beyond expectations

I ordered this because it looked a lot like mine that just died. When I unboxed it I thought it looked small so I measured it, the listing for this said it was ‎ 25 x 16.25. The one I received was 20 1/4 by 12,and the bowl in it was really shallow so it's being returned. I've already ordered another and hopefully it will be the right one. It's the one the next size larger than this one.I will leave a review on that one as well. I hope somebody gets it right.Ok, got the new one this morning, the description says it is ‎ 24.7 x 15.9, but it's the same outside as the one I just returned, the bowl is a lot deeper on this one though so I decided I would just keep it, or that's what I thought anyway. I set it up to try it out but never really got the chance. After filling it with cleaning solution it started leaking on the work bench before I even got it plugged in and turned on, Not just a moist spot but a leak that was running out from under it. The leak is coming from the central bottom on the drain end. So this one will be going back as well and hopefully I can find one that is what it says and works. I ewally don't like writing negative reviews, but this is frustrating

Great product and works perfect

I did not expect this sonic cleaner to be as good as it is.Working on my motorcycle, I needed to get something to clean my carburetor. I could have sent it to the shop and spend a $1000 or more.I chose to purchase one at a local store that was expensive and smaller than this one. My wife found this one and we ordered it and sent the other back.Used it this afternoon and I can honestly it lives up to its billing. It did perfectly well on cleaning my carburetor. I’ll have to dip it again because of how much gunk was on the unit but it’s a great deal cleaner now than before. The photo shows the dirty water after the first cleaning.