VeeBath Toilet Inlet Valve Bottom Entry, Inlet Float Valve 1/2 inch

Easy to fit and adjust great value good quantity

Good quality, the brass material for threads makes it strong and reliable

Thing of a beauty, a joy forever. Super easy to install, fits into the tiniest of spaces. I left the old flushing mechanism in the tank and just replaced the old cock and ball valve with this. It's quiet and fills up the 8 litre tank in under 30 seconds. (Compared to the 3 minutes before) Just make sure to twist the shaft and set the top of the blue plastic (critical level) to the height of the syphon's overflow. Then twist to lock again and insert the small plastic piece back to secure the position. Before installing the mains water, be sure to remove the piece of plastic from inside the 1/2" brass inlet at the bottom. Took me no time to install, no leaks or noise. ------------------------------------------------------------------------------------------------ UPDATE: After a week, it stopped shutting down completely and the excess water is now leaking into the bowl. Buying a Fluidmaster instead.... ------------------------------------------------------------------------------------------------ UPDATE UPDATE: After another week, it started working perfectly. No leaks or overflow. So in the end I kept it. I don't know why it had a hiccup but it gets plenty of use and has no problems.

Very good quality for the money. Delivered on time and decent price and packaging. It was very easy to install the new valve, run very silent and fill cistern in about 20 seconds. The old one needs almost 25 minutes. It took me ages to get out the old valve and bolts between cistern and toilet but that have nothing to do with this item . I found very easy to set water level by unclip the plastic stopper and twist the body then extended to the desired length. Very happy with the result despite I am not a DIY warrior and saved big money for the plumber. Time will tell how long will last but for now looking good and build quality is excellent for the price. The brass thread is very useful.

Easy and simple to fit and works perfectly

My family were getting annoyed with flushing as the old Eco valve would take 25 minutes to fill up! I did some research on Amazon reviews and picked VeeBath toilet inlet valve bottom entry. It was relatively straight-forward to install. Some tips: get a small container and towels to soak up any leakage. Drain the tank completely and turn off the isolation valve to stop water getting in. Take out the old inlet valve by unscrewing at the bottom of the tank. Before inserting the new VeeBath toilet inlet valve, ensure height is 3cm above the outlet pipe. Once installed, it would be almost impossible to adjust the height. Once it's installed, there is no need to over tighten the screws on the inlet valve. Get the towels and container ready and turn the isolation valve back on. Hopefully, there is no leakage. If there is any, it may be necessary to change the washers. Also, it's rather quiet filling up unless you are ultra sensitive to pin-prick decibels. Now, my family are pleased with the quick refill as it would only take 2 minutes compared to 25 minutes for the old Eco valve. I would certainly highly recommend Veebath toilet inlet valve bottom entry.

Much better quality than the one I took out. Valve closes positively. Fairly straightforward to fit with the help of YouTube vids. Brass thread better than the previous plastic one. My adjustable spanner size wasn’t quite enough, so would get a slightly bigger one when doing it again, improvised, but would make it easier. Added a bit of PTFE tape round the thread. Job done, saved a bit of money doing it myself.

It’s not clear from the product diagrams but the brass inlet is about 5mm shorter than my previous inlet, which in addition to the very thick seal meant it would not attach to the wall inlet. I managed to make it fit by using the original, much thinner seal and tightening it more than usual to compress the seal down. It then managed to just about connect with sufficient thread to attach to the wall inlet. That said it works - quick fill, quiet. Just double check that it is long enough for your cistern and water inlet. It works but buy with caution.

allt bara bra

Système de remplissage silencieux

Funziona a dovere

Really good easy exchange for the 10 year old one in the toilet very easy to adjust just a slight twist of the top and the you can lower or raise the water level the main bonus it’s so quiet when filling I had to check several times to see I had put the water back on very pleased the other good thing is the brass fitting on the end made it easier to tighten without the risk of stripping a nylon thread like done cheaper models

Funktioniert zu 100%. Mehr als hervorragende Funktion geht nicht!