Optic Adapter Plate for RMR Cut Slide Without Thread Post, Compatible with Holosun 407K/507K/EPS/EPS Carry/RomeoZero and Osight K/S/SE

First, this plate is perfectly machined... The Holosun EPS Carry almost snaps into place with a perfect fit. Outside footprint of the plate perfectly matches Trijicon RMR. A negative is that the plate is quite thick: .08in does not sound like much, but it is 2mm.... On the other hand, the plate seems very sturdy. I have a Sig P229 Legion with optics ready slide, factory-cut for RMR and DPP/Romeo1Pro. There are no lugs on the top of the slide, and the cutout is much bigger than the EPS Carry I wanted to install, so I wanted a plate to fill up the gap and keep the Carry from being possibly affected by recoil. This plate seemed to be the perfect solution, because I could screw the plate onto the slide with the RMR screw holes, and then screw the EPS Carry into the recoil posts of the plate (while also filling up the gap). Unfortunately Sig made the cutout in the slide slightly longer than necessary, so there is still a small gap... At this point I can either use no plate and bolt the Carry directly to the slide, or use the thin plate Holosun included basically as a gasket, or use this thicker plate to fill up most (but not all) of the gap. So if you have a true RMR sized cutout on your slide with correct RMR screwholes, this plate will probably be perfect. If you have an optics-cut Sig slide.... maybe it will still have a gap (but it is not the fault of the plate manufacturer). -----------Update 10/18/23------------ I finally decided to install this plate on my P229, and I realized the screws to mount the plate to the slide are not correct for this pistol. M3 screws are included, but I need 6-40. So if you try to use this on a P229 with factory RMR cut be aware you might need different screws. I emailed DPP Titanium to see if they can send the screws I need.

Super happy with my DPP RMR plate. Uses it to replace the other supposedly higher end plate & remount my Holosun EPS to my G19. The DPP is robust & strong yet thin, and it being thin was a game changer for me. Didn’t have to change my irons plus it’s keeps the whole green dot closer the bore. Wasn’t aure what to expect because haven’t had a DPP before & haven’t heard a ton about them. So wasn’t sure what to expect but figured I’d try it since the “high end” plate just wasn’t right. Was pleasantly surprised how nice it was & flat out blown away by the fit & function. Plus extremely affordable, a wildly outstanding value for the money. DPP has become my “go to” for pistol optic mounting plates. I’m not using anything but DPP going forward.

Great way to put your DPP optic on a rmr cut slide. Good fit and finish

Great product but the posts can get in the way if not needed. I used it to mount an Osight SE and it’s held great for a couple thousand rounds but had to grind the posts down to mount. Fits great really thin for the strength.

Seen a lot of reviews saying that this doesn't fir the dagger RMR slides. Mine fit perfectly on my dagger slide. Not too thick, durable, and easy to install. My Riton mprd x3 fit perfectly, no movement. Perfect function, overall great value for the money. For those saying that it didn't fit the dagger may have the wrong footprint.

Seems like a good quality part, however it does not fit PSA dagger rmr footprint as advertised.

Was searching for hours for this. I have a trijicon sro cut and this fit perfect for my new holosun HS507k x2 series on my g 19. I will order more in the future

I needed something to translate a footprint from an RMR cut to a DPP footprint for an EOTECH EFLX. This did fit the RMR slide cut perfectly, but it would not fit the EFLX without some modification. The quality and appearance seem great, and so far it functions great as well.