Mollom 4 Way Power Distribution Box with Bus Bars and Din Rail for Miniature Circuit Breaker MCB, Waterproof IP66.Padlock Available for Indoor and Outdoor Use

Nice IP66 Waterproof DIN Rail Case / Panel!This Mollom 5 Way HA Series panel appears to be well-built out of a plastic or resin-like substance, they call "PC+ABS alloy material".It has a DIN Rail and two small buss bar type terminal strips (all included) - One for Neutral and the other for Ground.The buss bars are held in a little blue plastic holder that snaps into place in the back of the unit. In the unit that I received, these buss bars were not fully seated (see photo), but I removed the blue plastic piece, and carefully bent it in the middle (toward me), and this let the bus bars fall into place. There are no guides for where you place your holes for your conduit or cable connectors, so use your best judgement and drill your holes accordingly. This unit arrived with three water-tight connectors (for PVC pipes or metal conduit, I presume), which I did not use.This unit comes in two shells that seat together nicely to seal out dust, insects, and rain water. The base shell attaches to the wall and the top shell attaches onto the base shell with four machine screws (included). The top shell has a clear plastic window, which allows you to view the status of your devices. The window is secured by green spring-loaded clips that are moved inward to release the plastic catches at the top and bottom edge. You can even place a small padlock, or an electrical seal on the cover window, to help prevent unauthorized individuals from casual entry.I used this box to secure a high power temperature control switch and circuit breaker to operate an attic exhaust fan. I am more than happy how the project turned out. This Circuit Breaker Box feels solid, and it looks good. I saw these products used in Europe, and was happy to install this one in America.I did not see any rating, such as UL, CSA, or CE on this unit. Maybe I missed it. If this rating is a requirement by your local electrical inspector or fire inspector, you might want to investigate this product's ability to be legally used in your location.

I am using this for some solar system din rail breakers. So far so good - just started wiring today. It is solid enough for my needs which are pretty simple. As with all these inexpensive Din rail boxes - the plastic wouldn't take much hard service. The holes are not knockouts - you can see the indentations but need to drill them out with a stepper drill bit which works well for that. If you need just an inexpensive cheap box this works and has enough room for wires. If you want something very rugged this would not be the one I would get - look for something made of heavier metal. As far as being waterproof - I won't find out since this will be used indoors.

For DIN rail-mount breakers there's a problem with "how" when it comes to small enclosures. This solves that problem quite nicely.I like the top and bottom holes and included rubbery glands for both, (in two sizes) so you can feed cables in with moderate environmental protection. You can also fit a compression gland if you intend to install outdoors (e.g. rain) protection that will stand up to abuse, but the provided rubbery ones are fine for inside.There is sufficient space on the side of the breakers and box for *some* cable routing back through the bottom for the top end of the breakers, but be aware that this depends on the gauge of the wiring you are using. For heavier gauges it is not going to fit thus you'll have to feed from the top AND bottom, but for 14ga (for example) it does.Tolerances are good, the "smoked" plastic front door is nice to prevent accidental actuation and the provided rail in side fits properly. Four places pre-indicated on the inside make for an easy install; they're not penetrated through so drill the one(s) you want and the cover screws are separate and provide a good seal with the pre-installed gasket.Recommended.

I have not installed this item. It arrived well packed and intact. It appears well made with no defects. All parts are aligned properly and move as they should. I recommend this product.

I used this to make my own breaker box for my solar system breakers. It worked good. It would have been nice if there were more knock outs but I just drilled holes. It's waterproof. All my din rail breakers fit perfectly and the box looks great. Overall very happy.

Worked well no problems

This brand has always been good. At least those with N and Gnd Buss bars. Makes wiring much easier.