Rubio Monocoat Wood Oil Finish 650 ft² | Oil Plus 2C | Quick-Dry, Eco-Friendly Linseed Wood Oil for Indoor Use, Includes Accelerator (Part B) | Protector | 1.3 L, Pure

Resurfaced this knife block (photo) that used to be just natural color with the Charcoal shade Rubio. It has a nice modern tone and is perfectly matte, as if covered with a matte varnish (it is not). The block is made of a very hard wood and yet it penetrated quite well, despite the 220- grit finish. Perhaps it could have been even better with a 150 but I wanted a very smooth final surface. It comes in two bottles, one is the colored oil mix and the other is a transparent accelerator. You actually can use the same accelerator with different colors. Just mix them 3:1 and you’re ready to go. It takes time to harden, the manual says mix as much as you can use in 15 minutes. It can be applied with anything: a pad, a brush, a soft cloth etc. After leaving it on for a few minutes, wipe it off and buff it until the shiny part is gone and it is done. My advice is wear rubber gloves as this stuff penetrates every pore on your skin and doesn’t wash off easily. It has a very low odor and is not toxic for food usage after it cures. It stops being sticky after a few hours but the full cure takes about seven days. Repeated layers don’t change much in my experience, it is basically just one application. If any Cons I’d say it is quite expensive for this small bottle, I’d buy more colors if it wasn’t this expensive. Also as it is one application only and no poly on top (probably can do an oil-based one if needed) it requires a perfectly prepared surface with no stains or other problems. I recommend this product.

Always buying more of this, really great coverage, and true to promise you only need one coat. I’ve only bought pure and it has the ability to pop the grains in hardwood and bring out the character like no other. 5 out of 5, great stuff.

I love this finish. This was my first time using Rubio Monocoat's Oil Plus 2c. I hate spending hours on milling, joinery, glue-up, and sanding only to get disappointing results with the finish. Rubio Monocoat is a simple but amazing product that has become my new go-to. I always thought Rubio was expensive, but I never really considered how much I was spending on stain and topcoat, not to mention the extra time and effort. I love how simple it is to apply and how little product you actually need. A good spreader or scraper is important to get the coverage you want. When I mixed it up based on the expected coverage, I didn't think it was going to be enough but it was more than enough. Once I buffed it in, the finish revealed a beautiful grain pattern in the desk top. I used the Pure color (or lack of additional color) on walnut and it’s gorgeous. The finish provides great protection and looks fantastic. It does have a slight odor for a couple of days, but that fades quickly as it cures. I can’t say enough good things about it, I love this finish. I consistently get perfect results, and applying it has turned one of my most hated parts of woodworking into one of my favorite.

If I could give this product 10 stars- I would. Was extremely easy to use. It has minimal to no odor at all. I purchased the shell gray stain with accelerator to use on birch butcher block countertops. If you follow the exact directions provided on the manufacturer’s website you can’t mess up. I combined the 2 bottles in a cup, mixed well. Used the plastic scrapers to apply even coat of the product all over the surface. Make sure you work with smaller areas. Spread the product; wait 5-ish minutes and buff it off. Used a sponge brush for crafts to coat the edges then wiped those after 5 mins. I used the blue shop towels to buff off any excess product. Application wasn’t messy and it was extremely easy to work with. After buffing off excess, it took about 45mins-1 hour for the butcher blocks to feel dry to touch. The stain dries to matte finish. I purchased the small bottle+ (130ml) and that was enough to finish an 8ft x 2ft + 2x 4ft x 2ft slabs of butcher block. The color of the stain came out a bit darker than what was shown on the pictures provided with the product- but I did expect it to vary, considering my butcher blocks aren’t made of oak wood as the sample in the picture is. Mine came out darker than shown, and I’m very happy that was the case. Reason why I picked this product is 1) because of its fast curing time. The counters should be fully cured in 5-7 days. Ready for installing and light use after 2 days. 2) huge upside- it only needs re-seasoning every 5 years. 3) does great to protect counters from staining. And it’s virtually completely water proof. This was extremely important since I’ll be using them in my kitchen. All in all- perfect product- fast cure time- easy to use.

Update 1 year later -- bumping to 4 stars. While it still "micro scratches", I've been pleased overall with durability and it's not as if someone else would view the wood island as totally scratched up. The surface been a workhorse for a year and I've been less careful, and while it doesn't necessarily look "like new", it looks good and most wouldn't know the difference. The early returns on scratches caused me some concern that I might have to abandon the finish, but I'm now planning to stick with Rubio monocoat. The scratches definitely fade over time although I can easily point many out still. Using the surface spray soap and occasional universal maintenance oil helps. And the fact that I did 2 initial layers. In the end, I'm happy with the choice of this for a high use kitchen island with the understanding that's it's higher maintenance and cost than traditional polys (and I'd suggest to use the other Rubio products for maintenance + hand sanitizer spray occasionally if you need to disinfect well), it provides a nicer feel/look with an easier application and less odor than the platicky poly finishes. So, if you're okay with those trade-offs, then it can be a good choice for a kitchen island. The pros/cons indicated below still apply though. I think a matte poly (harder to find) would also be a reasonable choice if someone wants a more scratch resistant surface, but doesn't give quite as nice of a feel/look (and smells much worse at application time) and sacrifices easier repairability. Update 6 months later after using it as a kitchen island/working surface -- liking it overall, still scratches: This finish does a solid job of resisting stains/spills. When I spill a drink on the countertop, it beads on top and is easily wipable. I still tend to wipe things right away so as to not test my luck, but if something small was left overnight, it's not a big deal. It still scratches fairly easily although the maintenance oil does soften the appearance of scratches but doesn't eliminate them. I apply a new maintenance oil coat once every few months. I do like the finish look and feel, and might bump up rating to 4 stars...I use the Rubio Soap regularly to clean it, which works well, but that doesn't disinfect, so I use an alcohol-based hand sanitizer spray when I need it (e.g. raw meat got on it) which seems to work well (Rubio used to sell an alcohol-based product to disinfect). To summarize, Pros: Looks good Feels good Easy to apply Smells good Resists spills/stains well/beads on top (still, wipe immediately) Repairable (although I have yet to re-sand and apply new coat, but simply applying a new coat of maintenance oil does restore it somewhat) Cons: Expensive High Maintenance Poor Scratch Resistance compared to more traditional finishes Original review: Using for a wooden kitchen island (maple butcher block). Applied it about 6 weeks ago. Did two coats based on recommendations here that it gives extra protection (and followed manufacturer's recommendations) + added Rubio Universal Maintenance Oil for additional durability (and then ANOTHER coat of maintenance oil two weeks later). The maintenance oil replaced the "high traffic" product that Rubio used to sell for hotels and commercial flooring applications. I figured all that would give it as good of a shot of durability as I could. This stuff smells nice, is easy to apply, looks really nice after application, and all that. It does seem to resist water/spills/stains although I've been fairly careful to wipe things up quickly so haven't fully tested sitting water or if certain products would stain it. However, my island now scratches ALL THE TIME. Maybe a kitchen island that is heavily used isn't the best use case for the product. Move a plate? Scratch. I knew it wouldn't be as scratch resistant as a poly, but figured it would offer at least some scratch resistance and the repairability/look was worth the tradeoff. I also got the Rubio Soap so I've bought into all the product line (3 different products) and spent a fair amount of time and money. Right now, I'm undecided if it was a wise choice to go with Rubio Monocoat or if I should have simply done a matte oil-based poly for a similar look with much less maintenance/cost. I am hopeful that after several months or a year, I can simply re-apply product or sand and re-apply and a "like new" surface will be there for me without too much effort. If I can do that, perhaps it's worth the extra maintenance but certainly, it's not close to a maintenance-free product like a poly would be (of course, poly is much harder to "start anew.") Depending on how that turns out, I am debating sanding it off and simply applying a poly, which would totally negate the benefit of Rubio Monocoat in the first place (easy repairability and look/feel of nature wood) and make it just a really expensive clear stain, which would have been silly. The kitchen island is a working surface that I use frequently (although I never cut/work on the surface directly), so perhaps going the traditional route would have been much easier and lower maintenance going forward for this type of use case. I saw some scratches in the first couple of weeks and applied another layer of maintenance oil and it did somewhat diminish the sight of the scratches, but didn't eliminate them. We'll see how the surface looks after several more months of wear and how applying more maintenance oil "brings it back to life" (or doesn't). So, I think Rubio is a great product for the right purpose. If you're planning to use a surface a lot and don't want to deal with maintenance, a poly solution might be a better fit depending on your particular wants/needs.

A littlr goes a long way if you trowel it. I used a bondo spreader it worked great. I love the color on white oak. Just make sure you wipe off the excess! Very easy to apply but unforgiving if you miss excess. It can look clumpy and if you try to sand it off it will turn white and be very noticible.

I have had this stain for all of 4 hours and already felt the need to write a review. We are renovating our house and installing butcher block counters and discovered the distinct lack of food safe stains, especially dark ones to fit our desired look. This stain SAVED us, after an attempt with another stain that looked nothing like it was supposed to, I was having a spiral moment thinking I was going to have to decide between something food safe in my kitchen or the look I wanted. Then I came upon this stain in a blog post and after a few minutes of research had it ordered. Now it is pricy yes, but after the aforementioned stain failure, this stain actually saved us money by not having to by all new prestained countertops that weren’t even food safe either. The stain is super thick, was easy to apply but definitely recommend using the plastic applicator (or an old ID card like I did) to save product. A cloth soaks up a lot. The smell is a lot better than typical stains as well. Color was exactly what I was looking for and matched the picture perfect. Oh yeah, and saw somewhere on their website about how they plant a tree with each order, that’s cool. Placing my next order now!

I think part B was shorted, hadn’t enough to mix with the whole can, so I contacted them. In no time they sent me an extra part B. As for the product, it looks so good on the walnut hard wood. The whole bottle is only enough for one dresser. You need to buy bigger bottle if you have more than one cabinet dresser size. Need to wait 3 weeks for the smell to disintegrate.

We use Rubio monocoat for all of our woodworking projects. We love the finish and the fact that it is food safe. It is easy to apply and actually has a pleasant smell. Very nice to work with. Highly recommended.

Good oil, easy to apply and I'm happy with the finish. Worth noting, this colour is not a paint, but an oil. It simply tints the natural colour of your wood. I was able to increase the strength by applying a slightly thicker layer, leaving overnight and rubbing off the excess before applying the cure

Très bon produit mais attention ne pas prendre le nuancier de Amazon il est incorrect, prenez le nuancier directement sur le site du fabricant .

I can safely say I’m now a Rubio Monocoat convert! I’ve tried this a few times but didn’t really like the overall matte finish. I always used Osmo PolyX gloss for a good sheen on epoxy tables and place mats. I had an order recently and the customer requested a matte finish and I happened to have a small 100mm bottle of the pure Oil plus 2c and gave that a go. After the finishing process literally being one coat and completely dry in less than 24hours it got me wondering if this finish is actually good… but I need a higher shine to my pieces. Got a small 100ml kit of the SheenPlus and I can safely say I am 100% converted to Rubio. 48hours and my finish is done! It was taking me 5-6 days with Osmo and stressing me out with the uneven dull finish until coat 4+. Rubio has eliminated that completely. I’ve even tried applying oil plus 2c in the AM and then adding the SheenPlus in the evening to cut down time even more with good results. While the weather is hot I think you can get away with it but doubt this will be as successful during the winter.

Super calidad de tinta y protector ,uno piensa q el costo es alto pero vale la pena por que no se desperdicia ya q abarca una gran superficie con tan poco