G2CR19X C1 1/2 in. NOM Comp Inlet x 3/8 in. OD Compression Outlet Chrome Plated Brass 1/4 Turn Angle Valve

I like this quarter turn valve, it looks really good and it is working great.

This is a decent valve. More and more often I end up buying hardware from Amazon because the pricing is the same, it's delivered to your door, and you get to skip the "moron-athon" at your local hardware store. However, I am giving you a WARNING that may save you some grief. If you are replacing 25 year old multi-turn valves with these, even though the size is the same...they are NOT. Internally, the size of the ferrule and dimensions required to seal are different. Here is what will happen: you'll pull off your old valve and discover you can't get the ferrule off. Out of desperation, you'll try to reuse the old ferrule and it will leak. My suggestion is to buy a 1/2 inch compression sleeve puller BEFORE YOU START. These can be had on Amazon for 11 or 12 bucks with free delivery. Also, just to be prepared for the worst, get yourself a foot of 1/2 inch copper pipe and a couple of sweat fittings. My valves were fine, I was just replacing them because they're old and the sink and faucet were getting replaced. My point is that you could go from no leak to a (potentially) serious leak, just by not being prepared. I'm shutting up now, just trying to save somebody an emergency trip to the hardware store (which I did not enjoy)...:)

I needed to replace some bathroom sink valves, and when I went to turn off the under-sink shutoff valves I found the shutoff valves to leak badly from their shaft packing. I decided to replace the shutoff valves and ordered these right-angle 1/4 turn stopcocks. I found these to be well constructed and of good quality. Installed without any difficulty and when the system was re-pressurized, they worked like a champ, no leaks, and good flow rate when opened.

Excellent quality and relatively easy to install. Be sure to have a compression ring puller on hand though!

I used the quarter turn valve to replace the Brass Craft gasket style valves that were originally installed under my Kitchen sink for the hot and cold water and the dishwasher. I used Brass Craft because they would fit the already installed compression ring and lockdown nut. The valves are easy to install, even if you removed the existing compression ring and put on a new one. It only took a few minutes per valve. They don't leak and they completely cut off the flow of water to the faucet and the dishwasher. They do everything they are supposed to do. I'm not a plumber but I am an electromechanical tech, well I used to be a long time ago. It didn't require any special skills to install the valves and I believe most novices could do it. I recommend the valves and if you're replacing 12 year old gasket style Brass Craft valves, you're making the right choice by using these since you can use the existing compression ring and lockdown nut.

This item is so much better than the items available locally. Most of them have plastic parts inside. They just don’t last. Especially when used on the hot water side.

Good value for the quality. Received it very quick as well.

This product is awesome. It fits over your old compression outlet so really you only need to remove and replace the body but leaves the tighten nut and compression ring from before. I'd clean as much as possible of any old debris and covers the compression ring and all of what you're going to tighten back with some Allstar Performance ALL14282 1/2" x 260' Pipe Thread Tape or any brand you like to add extra leak protected. Believe me, you'll need it. If possible, give it an extra mm of the thread tape for more leak protection over the mouth ring so that when you go and put in it a new body, there won't be a leak. DON'T leaves the mouth expose is what I'm saying. My advice is when you use the tape, go in the same direction that you're nut is going to be when tighten down and when you go and put in the body, rotates it along the direction of the tape. You don't want to go the opposite direction of the tape. Then tighten down the nut and you should be fine. I'd buy this over the SharkBite Stop Valve because those are not one size fits all. All of your PEX or CPVC in your home may not fits it all even if they are all the same brand and size. My hot water tube from up stair did fit like the others but it still leaks. Tried using several but each one still leaks. I tried covering the body with tread tape and they still leak. So basically, I highly recommend replacing your stop valve with this product. Make sure you followed how I did it and you should not worry about it for another 25 years. I know I won't because I just replaced old stop valves that are coming up to 25 year old.