Vevitts Small Brushed Permanent Magnet Electric Motor for E Scooter Drive Speed Control 24V 350W 3000RPM

So far, so good. Purchased this as a replacement of the stock Razor MX350 motor and I gotta say I noticed a difference. Better torque and didn't overheat with me riding on the bike like the original would. Easy to install as the mounting plate aligned perfectly with the bike frame. Time will tell on durability. My son rides it and is a bit over 100 lbs and noticed better response time.

Really woke up the kids Razor MX350s. It paired very well with the “fast scooters” 36v over bolt kit and 36v lifepo4 batteries. They’re ripping now and for the speed increase and money it’s hard to beat their value.

Very nice

Worked perfectly on a razor mx350.

I just received this motor this afternoon. I took it out of the box and inspected its condition. Around the holes in the feet for mounting, there were some odd raised areas in the paint that looked like bubbles. I took a small chisel and a little grinding bit on my dremel and was able to pry up a little of the paint or powdercoat, whichever it is. There is rust underneath. The metal was obviously not prepped properly before being coated, so there is likely way more rust than what i can see. I thought about taking the housing off the motor and sandblasting/repainting it, but its brand new and shouldnt need it. Returning for a refund. Problem is, this style motor are rebranded a thousand times on amazon so theyll all be from the same factory. Guess I'll just keep ordering until i get one that was properly prepped and at least doesn't have rust bubbles under the paint.

So as you can see here I have a razor mx350 I got a couple months ago to ride with my girlfriend around town and junk and it's been really fun. That being said she's about 50lbs lighter than me so her stock bike would go 1-2 mph faster and she would just abandon me on adventures free as a bird (tbh who could blame her.) naturally I got sick of being slow quite fast so I upgraded the entirety of the power delivery system to 36v with the help of jordybuilds and a fancy battery I got from here I believe a cao mm battery. The bike was fast as hell hitting 21 on flat (given a 50% power boost I'm not shocked to get 50% of the speed added as well) the thing was an absolute power house. Only problem was that stock mx350 motor produced uncanny amounts of heat on a small 2 mile scoot. So I ordered this on a whim and replaced the stock motor. The bike now runs a solid 22 on flat with a full charge and can easily go 5 miles before the heat starts to become super noticeable. I haven't taken it further than 5 miles (waiting for a my1020 motor as a backup just in case this vevitts dies but it's seeming less likely by the day.) the motor is fast runs smoothly and handles the overvolt like a dream. Given the 20+ miles I've out on it in about 3 days I can't say enough good about it's performance The only cons I have for this motor is that the leads have VERY minimal shielding. I made sure to wrap them about 4x in electrical tape to try and keep them protected but I do think it's something vevitts should consider in the future. Maybe a slightly thicker gage on the leads as well they are a bit small to mount into the plugs for the original motor on the mx350. My motor also shipped with a slightly bent mounting bracket however I got 3 bolts in and it's solid/straight enough so I'm not pressed. All in all it's about a 3.8/5 and climbing every day as I abuse it. Would be happy to find the information for this company and work with em directly on something silly small and stupid like this again. Good buy

This fits perfectly on my son’s razor dirt bike. The motor works as it should and doesn’t get overheated.

This motor did work well and fit my e300s OK in the space properly except for the bracket mount itself. The holes in the bracket are tapped holes where my previous motor mount was not tapped. My original bracket also had countersunk areas where the flathead cap nested into the bracket. On the new motor mount screw mount holes I had to create the counter sink area with a counter sink tool and open up the holes with a 1/4’ drill bit,so the mount had some free play to fit between all 4 screws and the screw tops were flush like the original, not stand /stick up . See my photos.

El producto llego rápido y salió muy bueno!!

An awsome motor,just need to replace the pinion gear to my wheel sprocket,for the same chain ,which is t8f chain,which is a challenge, but I will fab it to fit.

Good

Le moteur est très puissant

I have placed a rotary encoder on the shaft and measured 2995RPM this motor according to my mesurements is a beasttt. Have not connected it yet to a system will give news.