Forward Sling Mount Remington 870 & Mossberg 500/590

I looked and looked and looked for a quick release sling connector for my Remington 870 to no avail. Something of high quality, not composite - otherwise known as plastic - and not a rail mount. I did look at the CDM Gear BMT with 3 slot rail - Shotgun Flashlight Mount, as I wanted to mount my Surefire too, but its expensive and I wasn't 100% positive it would accomodate a quick release swivel. This is it. You can attach a AR style quick release sling connector to the front of your shotgun with this. You can also leave the original sling attachment or remove the one that comes with this mount - on or off, right side or left side. They provide two small nuts that replace the Magpul ring which I did. The only drawback is that this mount locks the quick release into place, it doesn't swivel. The original Magpul mount ring does not swivel either. There are four positions you can lock the quick release into, so it works fine. It is also a much more stable and better looking forward tube connector than what was provided by the factory. Highly recommend and super easy to install. UPDATE: After a defensive / tactical shotgun all day course I wanted to update the review. After approximately 150 rounds the bracket had moved all the way up the barrel to the front of the shotgun. It also left a huge scratch on both sides of the feeding tube. Apparently this is not a unique incident. It happens, so be prepared. This is not because it was not not cranked down and tightly connected. It's just not perfect. The scratches on my shotgun really annoy me too.

Great for being a barrel clamp while also being a minimalist for barrel real estate. Takes everyday wear and tear like a champ and hasn't failed me yet, like any quality product from Magpul. Installing it is a bit of an ordeal. The clamp came with two nuts, my Mossberg only had enough screw space for one nut for the included screw to grip onto.

This is a very good piece of equipment. It combines a clamp to keep an extended magazine tube atatched to the barrel with a two-position pushbutton sling mount. The mount is all steel, and comes with one removable sling mount that can be placed on either side. The receptacles for the sling mounts are universal and you can use other manufacturer's mounts as well as the one that comes as part of this package. The receptacles hold the sling mount in one of four positions, they do not turn once they are inserted like on some other mounts. This can be seen as an advantage or a disadvantage depending on what you're used to. The mount is held on by a machine screw and nut that are removable. This means that the kit has five parts total. The kit comes with small silicone pads to prevent marring and to give a slightly "sticky" surface so it's not just steel on steel between the mount and the barrel. I originally rated this 4 stars instead of 5 for two reasons. First, the sling mount receptacles are on only the sides. It would be nice to have a bottom mount option as well. Second, the screw that holds the two halves of the mount together is slightly too short, and getting all the parts lined up and fastened tightly is a little difficult with only two hands. After using the mount for a couple of months, I've upped it to 5 stars. The side mounts alone work fine with a side mounted rear sling, and I don't remove and re-attach it enough (never so far) for the short screw to bother me. Overall, this is a very good sling mount and mag clamp and I would recommend it to anyone.

Great product. Great quality. Best I've seen on the market at a great price. The product description was spot on. For 500 and 590. Did not fit my 930. Had to return. Bummer!

This accessory is generally well made and appears to function properly on my Remington 870. However, the installation is a pain: lack of tools and horribly incomplete instructions. First, tools. The installation of most Magpul accessories requires an 1/8 inch hex wrench; which is usually provided. This mount requires a 9/64 inch hex wrench; which was not included or cited in the so-called instructions. Probably explains why some reviewers have reported issues tightening the screw. Second, instructions. Both halves of the mount have one end marked '05'. The other end is marked '4' on one half and '8' on the other half. The '05' ends are longer and have a larger radius. These ends fit the magazine extension tube. The '4' and '8' ends are shorter and have a smaller radius. These ends fit the barrel. Insult to injury, these markings are covered after installing the silicone pads. Now, every time the weapon is disassembled, care must be taken to ensure the halves are returned to the proper orientation. Absolutely zero mention of these details in the so-called instructions. The barrel and magazine extension tube have over 1/10 inch diameter difference. Unless the halves are properly oriented, installation could be unreliable, if not dangerous. Furthermore, on the production unit received, the sling mount only aligned properly (parallel or perpendicular to the barrel) on one of the halves. On the other half it was cocked. The hex socket on the screw was slightly malformed. Also, odd that spares for the nut and silicone pads were provided, but not the screw. First time I have ever been disappointed with a Magpul product...

I'm happy to say I found a Bbl/mag clamp, and I wanted a forward sling point too, here it it is! I tried 2 different tin clamps on my Rem 870 ext. Mag/Bbl and none would fit right. I spent a little more for a Magpul, and i'm very glad i did. Its very sturdy, looks good, has a Forward Sling Point and it fits my 870. Magpul is all about quality and worth the price to me. It even comes with 4 silicone form fitted pads that go where the mount touches your barrel and mag extention so you dont scratch anything (nice touch). I'd recommend this to anyone.

I bought this because there are few aftermarket options for the Ithaca 37. It will fit and work fine without fitting but if you want a perfect fit, you'll need to get out the files and its pretty hard steel. It is extremely robust. The only thing I didn't like was that the sling loop is canted, I mounted it right side for left handed carry and it cants forward, not a huge deal and I'm still pleased.

Have this on my Mossberg, rock solid and sturdy mount to run a sling to. Do not over tighten it though, as it will cause feed issues due to binding in the tube. Install was easy, this is another really great accessory from Magpul!

Besides fitting Mossberg 500/590A1/590/Maverick 89 and Remington 870/870 Blueline clone 12 gauge shotguns, it also fits perfectly on the Stoeger M3000 series and higher numbered Stoeger semi auto and pump action 12 gauge shotgun models, I got it for my M3000, it also fits the Beretta 1301, A300, Benelli M2/M3/M4 and the clones, the clamp is slightly smaller than other barrel clamp brands but it still looks great especially if you want something slightly smaller and sleek, it’s also genuine MAGPUL quality and made of steel not polymer, I’m really happy with it, it also comes with 2 packs of little silicone pads you peel off and stick on the little square indents on the inside surface of the clamp, you’ll see it when you look at it, it’s to prevent scratches and wear to the finish of the shotgun barrel and mag tube, plus it gives the clamp more friction so it’s less likely to move under recoil, the screw for the clamp has a bit of yellow loctite on it but I still added a drop of blue loctite to the screw just to be sure it won’t unscrew itself, they say to tighten it to 23 inch pounds I think with a torque wrench, but I just tightened it by hand with an Allen key, don’t overtighten it as to not strip the screw, it’s rock solid on my shotgun, really nice!

870.1100,11-87のロングチューブマガジン装着の銃に使用。 三種類で使い回せるので便利です。 薄いスチール製の物だとスリングを付けて 猟場を動き回るのに不安がありました。 こちらは、ごつくて頑丈そうです。

Un accessoire Magpul de qualité!

モスバーグm500に取り付けていましたが、分解整備や銃身の交換で毎回外すので使用するのをやめました。

Made of cast or stamped alloy. High-quality manufacturing and polished, burr-free. Small silicone pads are included; they should be applied to the square recesses on the inside of the clamp to prevent movement and scratches on the barrel/magazine tube. The barrel and magazine tube loops are precisely machined to fit so they cannot be confused. Ideal for 12-gauge shotguns, but a longer screw is required in some cases. Magpul undoubtedly stands for quality.