Oshlun LG-M01 Miter and Portable Saw Laser Guide, Miter & Portable Saws , grey

My miter-saw came from the factory with a built-in laser. Problem is, as you use the saw the laser tends to wander, until ultimately you can't rely on it, at all. This is a super solution to that problem. It mounts directly onto the arbor, on top of the blade (on the side) with the nut locking down on it. This gives you a very consistent, and very accurate platform. I am extremely pleased with the improvement in the accuracy of my saw. It even comes with the batteries included. This is such an easy fix, and works so well I cannot help but recommend it. I also feel that it's an extremely good value.

First off, I had an older Irwin red laser for my saw that I have had for well over 15 years.. When the unit gave up the ghost I knew I wanted one in Green Laser as the red just washes out too easily in bright lighting. The other thing that is in contrast with the Irwin that died an the new Oshlun is accuracy of line projection.. My Irwin had approximately ~3/64" deviation from the blade kerf and the projected line.. The Oshlun.. This thing is dead bang with the same blade, kerf to Bright Green Line. Well done OSHLUN!!!

Lovely tool accessory! Makes cutting much more efficient. I had a fit issue though, was too loose on the arbor screw and had to turn a small bushing for it on my lathe. Bosch 8.5 inch miter saw,

Great product. This laser guide is more accurate than the OEM shadow guide with my 18V HP Ryobi miter saw

I have used an Irwin red laser, with very similar construction, for 20 years on my Dewalt compound, sliding, miter saw. I was a little skeptical that the green laser would be significantly better than the red laser line I already had, but I decided to try this because the red line has always been hard to see. I am very pleasantly surprised. The green light (from laser) is PROFOUNDLY easier to see and it lines up PERFECTLY with the left side of my blade!! My old red one was a millimeter off to the left of the blade and always had to be compenstaed for. I am very happy that I decided to try this light by Oshlun. It's worth every penny.

I’m quite happy with this accessory. It was easy to put on and doesn’t get in the way of anything. I put it on my 10in Bosch glide saw. I didn’t have high expectations for this but it is extremely accurate. I never take the saw out of my shop but I could maybe see on a job site or having it outside, that the laser might be hard to see. I haven’t tested this but in my shop, I have no problems at all seeing it. I didn’t want to go through the hassle of putting on a shadow line accessory and this seemed like a good value. I thought maybe it was going to be too large but like I said, it fits very well and doesn’t get in the way of anything. It’s been going strong for 6 months now and I’ve had no issues. Again, I haven’t tested this theory but I think it’s design will allow it to be used on just about any miter saw.

Not nearly as bright as advertised. Barely leaves a green line on the material being cut. Need the room darker to see the line. I would not buy this again.

The summary: This is a great add-on for your miter saw! The review: After reading all of the reviews on different laser guides, I was a bit concerned about the accuracy of any of these devices. (A lot of reviews have complained about 1/8-1/4" inaccuracy. True, these are for different models, but I assume all models are all about the same.) But for [...] bucks, I figured it was worth the experiment. Also, I read on a few reviews that these things can be adjusted, so I figured I could always do that. The guide arrived and I installed it, I was pleased to find that the laser line was *exactly* where the blade cut. This thing is spot on...no need for adjustment! It was easy to install, and fit my off-brand saw with no problems. I only have two small issues (things of note, really): 1. In bright sunlight, it can be a bit hard to see the line. It is still adequately visible, but not a huge bring line like some reviews might sugget. I assume that all lasers will be about the same in this regard, however. I don't think that Oshlun's guide will be any dimmer than their competitors. Luckily, I live in Seattle where the majority of days are at least a little grey. In that weather this laser guide shines bright! (Also, it is possible that the batteries that shipped with the unit started to weaken in the package. Perhaps if I changed them with the extra set that came with the unit I would find the line brighter.) 2. One needs to activate the saw blade to see the line. Again, it is hard to fault Oshlun for this.....all add-on laser guides act in this manner. It would be very dangerous for them to put a switch on the unit, as that would mean that people were always reaching their hand near the blade to turn it on. And they can't make the laser stay on after the blade stops, because the saw blade needs to rotate in order to produce a line from a single point of light emission. But if you are buying this unit, you should know that this is how these devices work - oshlun and otherwise. I didn't remove any stars for these things, because I feel that it is still a great product. I just wanted to note them for anyone else interested in purchasing this unit. Overall though, I would say that this is a great unit. If you are looking for a laser add-on for your miter saw, go for it!

I purchased the Oshlun LG-M02 laser guide for my AEG PS-305 DG 12" compound mitre saw. The existing laser guide on the saw had broken and was no longer available. The Oshlun laser guide works well on this saw, however I had to replace the existing counter-sunk M10 left hand thread arbor bolt with a non-countersunk bolt (30mm worked well). Based on my personal experience, I would recommend this device for the AEG saw if the original laser guide part fails.

funciona excelente, fue un abuena compra para cortes exactos

O produto é muito robusto e cumpre o que promete. Muito preciso na indicação da trilha de corte. Apenas aconselho a verificarem a compatibilidade com a sua esquadrejadeira, no meu caso, uma Stanley SM-18, tive que fazer pequeno (0,5mm) ajuste na arruela do disco, para que o laser desse o aperto necessário ao disco. No mais, funcionou com muita precisão.

Utile mais très chère en plus il ne fonctionne pas tout le temps il a falu que je le modifie pour l adapter

Works way better than i thought. It makes a nice line exactly where it’s going to cut. Just slightly off to the side. On the left. But seriously, it’s way better than i thought. I love it. It’s actually useful. Great device. Works good on the bosch glide saw.