for MagSafe Sticker, MagSafe Ring for iPhone 17, Samsung Galaxy | 2 Pack Metal Ring, Universal Magnetic Wireless Charger Conversion Kit for Google Pixel 10, Magsafe Accessories, Black

Got one of these for my Pixel 6a in an OtterBox Commuter case. I couldn't use the alignment tool because of the USB C cover on the case so I had to position it manually, which was oddly more difficult than I expected. After a week I ended up removing my first attempt because it wasn't quite in the right place for my grip, just a quarter inch too high, which really leads me to my one complaint about this otherwise great magsafe ring: the adhesive. It adheres extremely well to the rough texture on the back of the Commuter case, actually a bit too well. It was very difficult to pry up an edge on the ring, and my spudger ended up cutting into and smearing the adhesive around as I was working my way around the ring, leaving much of it on the case. I'm not sure what this material is but it's very sticky, breaks apart easily, and leaves a strange residue behind. An almost gum-like consistency. Some goo gone, rubbing alcohol, and elbow grease, and I was back in business, but man, what a pain. Swap that out with a nice 3M adhesive, something that tends to remove in a single piece, and can even be repositioned, and maybe include some or one replacement (even if it's a touch more expensive) and this thing would be perfect. Other than that, it's very thin and stylish, and it's rock solid with the magsafe accessories I've tried. I paired the ring up with the metal metisinno magnetic base and a popsocket, then the lamicall magsafe mount for my car. The latter fits right over the top of the popsocket and the magnets in the lamicall mount attract to the metal back of the metisinno base under it. I can leave everything as is when I move in/out of the car. It's the perfect setup for me, one I've been trying to find for years. At no point do I have any concerns about the strength of the magnetic connections between any of these. It takes real effort to separate them. Just triple check your placement of the ring, because you'll have a heck of a time removing it, and will not be able to reuse it after.

Comes with two MagSafe rings, which is already a nice bonus. I installed one on my Pixel Fold silicone case and it stuck securely within minutes. So far still good after a couple days — no peeling or shifting. Magnet attachment strength is great. Snaps right onto chargers and my OhSnap attachment with no problems. (Though you should note the ring is not a magnet itself.) Big win: wireless charging still works perfectly even with the ring installed. No interference at all. Fit is spot-on, install was easy, and everything just works. Pros: • Strong adhesion • Great magnetic hold • No wireless charging issues • Easy install • Two rings included Cons: (none so far) Would absolutely buy again.

I installed these ESR MagSafe stickers onto the inner case of my Samsung Galaxy S23 Ultra and Samsung Galaxy S22 Ultra OtterBox cases. I need to remove the soft outer case layer so that I can securely attach both phones to my OMOTON TP06 Magnetic Phone Tripod while taking photos. The magnetic hold and suction strength are excellent, and both phones stay very steady and secure during photography use. Using the ESR MagSafe stickers has made these phones much easier and more functional to use for taking photos, whether handheld or mounted as a tripod setup. I am extremely satisfied because this setup gives me much more flexibility and functionality when positioning my phones for photography projects. I would definitely recommend these ESR MagSafe stickers to anyone looking to add MagSafe compatibility to older Samsung phones that do not officially support OtterBox MagSafe systems like the newer Samsung Galaxy S25 Ultra and Samsung Galaxy S26 Ultra models.

Comes with everything you need to easily apply the ring onto the phone in a small package: wipes, rings, alignment guide, and instructions. Its quite durable considering the thin profile. Sticks surprisingly well and roughly works on even the worst possible cases. Just make sure to clean the surface well and firmly press down and hold so that the adhesive stays on strong. Took some effort to take it off, had to bend my case to do so. It also holds on very well to anything MagSafe related, was able to lift up my Anker MagGo charging stand by the phone. However, one downside I found that leads to me probably not using it is the sharp edges on the ring. I tend to hold my phone quite close to the palm and in addition, "slide in" my hand to grab the phone. The sharp edges make it quite uncomfortable to grab my phone. Regardless, I'd suggest giving it a try even with the problem of the sharp edges as it'll depend on the way you use your phone meaning you may not even run into the same issue I have.

I'm using this in ways it says not to, so grain of salt here, but it works perfectly for me. - I'm using it on a Pixel 9, not an iPhone or the listed Samsungs. Since there are no templates included for the Pixel 9, I had to play around with placement for a while before I was comfortable that it would work for charging. I eventually found that one of the Samsung templates did actually place it very close to where I needed it, but that was only because the alignment adapter didn't fit all the way into the charging port as intended. See the photo for what I mean. But as long as you "practice" placement first to find the best spot, it can work on other phones not listed. (I recommend placing the ring on your magnetic charger magnet to magnet and then moving the phone around on top to find the best spot... then press the phone down to stick it.) - It adhered very well but I'm using it on a vinyl skin, not a case. So there's less interference but it could also be less durable since it's only as strong as the skin is. It's held up for the few days I've had it installed but if anything changes, I'll update, though I wouldn't fault the ring for that since I'm not using it as instructed. - The magnet is very strong. I use a magnetic wallet and it attaches much, much better than the Magsafe MOUS case I had on previously. That was strong enough not to lose the wallet but I could remove it quite easily myself. With this, the wallet isn't going anywhere and it takes quite a lot of force to remove it for charging. - It's super thin and light but holds well. I got white and it looks nice, even though it's obvious. I don't anticipate needing the second one unless something happens to my skin and I need to replace that, but glad to have it as a backup. All around very much recommend. And for what it's worth, I realized I own 2 other ESR products—the 3-in-1 travel charger and an iPad case—and both are great and very high quality. So I'm now on board with this brand at this point. We'll see if that continues. UPDATE 6 MONTHS LATER: DURABILITY: The ring has been working great! And still very white (no staining) and not a scratch on it despite the fact that I slide my wallet on and off and put the phone on and off a standing charger daily. However, I accidentally ruined my vinyl skin—dyes from a new pair of jeans I didn't wash enough first mreh—so since this pack comes with two rings and I had an extra lying around, I decided to just replace my skin/ring. This gave me a chance to try and destroy the old ring while it was still attached, just to see how it held up...... yeah, that sucker ain't coming off naturally heh. And it took a of scrapes but was still magnetized (and charging) just fine. I eventually just removed the vinyl skin with the ring still attached so I could move on. It holds up! TEMPLATE: So the SAMSUNG A template does indeed work for the Pixel 9. Last time, I'd discovered afterwards that this particular template was very close to where I'd eventually installed the ring after a bunch of testing. This time, I just went straight to using the template. So, I installed my new vinyl skin, plugged in the template attachment as far as it would go, put the Samsung template on rung A, and stuck down the ring. All is well. Worked like a charm!

For anyone to whom this review benefits know this: If you're looking to pair this up with a non-magsafe wireless charger with your magsafe case, know that this will not work for you. The ring holds next to no magnetic charge and its ONLY purpose is to turn non Magsafe Phones (or phone cases) INTO magsafe phones or phone cases. It has 0 value outside of that. Anyways, onto my thoughts below. Wasn't what I expected. It fits fine, the adhesion is strong, it was very easy to install and it was quite thin too. For $8usd I'm certainly not going to be too upset as it certainly cheap enough to not be upset about but it just doesn't feel like it did what I wanted it to. I was hoping this would be something where I could turn non-magsafe devices into a magsafe device. You know, so I could use my case and have it snap onto the metal ring and get wireless charging or holding something else. I do not think that this delivered on that front at all. Nothing about it appears to have ANY form of magnetic charge in the slightest, at least not in a meaningful way. It DID and DOES stick to my mag-safe case when it was just on its own, but once I applied it to the devices I was hoping would transform it into something I could more easily attach my phone to. It did not do this. Kind of disappointed. I can't give it a 1 star review because that would be unfair to the people who made this product, and this is merely probably an error on my own part. But I can't give it a 5 star review either because that would feel a little dishonest. Hopefully a 3 star feels fine enough.

It took me awhile to find this color. I got the Desert Titanium. Most had basic colors. But my case has mother of pearl that shows through and is so beautiful. I wanted a ring that complemented that instead of a flat color that would have made it ugly. This ring was the perfect color and it is a high standard ESR universal ring designed for MagSafe. I didn’t mind paying slightly more for the color I wanted for my non MagSafe case. It came with an alignment clip and guide that makes it super simple to attach. I have an iPhone 16 which is the exact same size as a 15 so I used the B on the alignment guide supplied. So it fit perfectly. The adhesion was great. I got it a millimeter off center and I couldn’t budge it. Oh well. I try to not let it bother me when I look at it which is not often on the backside. A little OCD…maybe. It functions fantastic. Even though I have a non MagSafe cover on my phone, with this ring, it attaches perfectly on my MagSafe charger and charges my phone just fine. It holds it really well without slipping at all. As for the durability, I’ve only had it a day now. But it is sturdy as can be and feels more than secure. Plus I have an extra in the pack just in case I need another one. I see no issues at all. I love my case and wanted to find a ring to work for MagSafe and this is it! My case had other colors so I’ll be purchasing another one now that I know I can use this great little ring to make it work with my wireless charging device. Happy as a clam!

BACK STORY: I really am satisfied with the MagSafe ring (Halo) holder / stand that I purchased some time ago, and have purchased several of them since then. I already had a case that I was really pleased with, but as it wasn't magnetic, I attached it using a several adhesive spheres from a third party and had no trouble. The case subsequently broke following multiple drops, but I bought the same one as I very much liked the case. This time, despite using the same MagSafe ring stand and the new pieces of the same adhesive, I couldn't get the ring to stay on. I even bought new adhesive, to no avail. I even purchased a new ring, just in case. That also wouldn't stay on with two other adhesives. REVIEW: I saw this listing and thought this item would solve my adhesion problem, particularly given the item description... "Upgrade to MagSafe Ready to Go Magnetic Want MagSafe but love the case you already have? With the HaloLock Universal Ring 360 you don’t have to choose. Just install to convert your standard case to MagSafe and start enjoying magnetic wireless charging and a whole host of accessories to snap on the back of your phone." It sounded like just what I needed. I cleaned the phone case as instructed then attached one of these rings. I gave it 24 hrs to cure, then attached the ring / stand, and everything fell off. The same thing happened with the second one I tried. I even bought a second set of these rings in case it was my mistake, but, for the third time, the ring would not stay on. Finally, I attached this adhesive ring to the back of my case using JB Weld (Professional grade) to attach this magnetic base to my case and it stuck. It held the actual Halo ring / stand on my phone with no problem. I've dropped the phone a number of times, and the ring stand has fallen off, but this magnetic adhesive base stayed on and easily attached that ring again. Other than the less than wonderful adhesive provided with these rings, I'm very satisfied.

Works with all types of magsafe accessories and is easy to install. I am using it with popsocket and magsafe power bank.

The product delivered to me was different from what’s posted. Looks like a cheap brandless metal ring. Does not have the additional magnet to help keep magsafe wallet in place. Still have to test if it will work properly with mag safe chargers.

Prodotto conforme alla descrizione, qualità ottima. Facile da applicare e funziona perfettamente con MagSafe. Venditore serio e spedizione veloce. Consigliato!

非常に磁力も強くて満足です

it comes with two magnets which allows me to put on two of my samsung cases. Very easy to install. Works extremely well with the ESR powerbank. Def recommend to people who wants to turn their samsung into magsafe with low budget.