Question 1

I need to define which cable is linked to each room in house as they all terminate in a single box in closet.  Will this define which cable is which?

Accepted Answer

Yes, but it will require patience and a bit of time.
First unplug all LAN cables from your switch or router in the closet.  Also unplug any computers or printers or switches in all of the rooms.  This tester is not meant to test “live” cables.  
If you are testing jacks (not terminated cables) you will need a tested jumper cable for each end (test the jumpers first).
Connect the master CT468 to one of the lines in the closet and turn it on.  I recommend the “on setting” to save time (the S is for slow).  Then go room to room with the CT468 remote and plug the remote in (if testing jacks plug in the known good jumper cable).  It should light up in a couple of seconds if that line in the closet goes to that room.  Once you get lights on the remote you have identified which room corresponds with the cable the CT468 master is connected with in the closet.  Let the lights cycle at least two times to check for continuity on all pairs in that cable.  If one or more of the lights do not light up or they do not light up in order (1 then 2 then 3 then 4 then 5 then 6 then 7 then 8) then you have a problem in that cable.  Note G is only for Shielded Twisted Pair (STP) cables, which are rarely used in a home environment.  You will need to repeat this process for each cable in the closet and each room.  Don’t forget to label each end.
Good luck and God bless.
V/R
Steve

Question 2

what does is mean the lights just keep sycaling?

Accepted Answer

When you are doing the test, the lights continue to go through the cycle 1, 2, 3, etc., testing the pairs. If there is a problem with a pair, the lights cycle will indicate by going 1, 2, 3, 4, 6, 5, etc., indicating a problem between pair 5 & 6. You might not see that the first time so the lights will just continue to run through the sequence so you can continue to see where the problem pair is located. It just means that the lights continue until you turn off the test. It works great and it’s very simple to use. Once you use it, you will understand what the “sycaling” means. It just doesn’t do it once and then stops, it continues to sycaling through.

Question 3

light goes on from 1 to 8 but g does not light. what is G for?

Accepted Answer

The G is for ground, if there is a ground is will show, if no ground is in the cable assembly not to worry. Most cable assembly's today do not have a ground.

Question 4

There are 3 different testers for sale, which do I need to test my cat 6 cables installed by electrician and my own cables? Connection is spotty.

Accepted Answer

One that does rj45. Cat6 cables have rj45 connectors. This tester will only tell you if the wires are connected in the proper order, not if the quality of the connection is good enough. That requires a much more expensive tester.

ASIN	B01M63EMBQ
Best Sellers Rank	#12 in Cat 5e Ethernet Cables
Brand	iMBAPrice
Brand Name	iMBAPrice
Color	Yellow and Black
Compatible Devices	Any device using RJ11, RJ45, CAT5, CAT6, or CAT7 cables
Customer Reviews	4.4 out of 5 stars 5,229 Reviews
Included Components	Network Tester and add on
Item Dimensions	0.41 x 0.41 x 0.1 inches
Item Type Name	Network Tester Rj45
Item dimensions L x W x H	0.41 x 0.41 x 0.1 inches
Manufacturer	iMBAPrice
Min. Operating Voltage	9 volts
Minimum Operating Voltage	9 volts
Model	BC-50W-P
Part Number	IMBA-NF468
Power Source	Battery Powered
Specification Met	Battery Powered
Style	Compact
Style Name	Compact
UPC	617689111530
Unit Count	1 Count
Upper Temperature Rating	60 °C

iMBAPrice - RJ45 Network Cable Tester for Lan Phone RJ45/RJ11/RJ12/CAT5/CAT6/CAT7 UTP Wire Test Tool

Details

Details

Description

Specifications

Reviews

Common Questions