Polarized Film Sheets 2 PCS 8x11inches/20x30cm Adhesive Polarizer Linear Polarizing Filter for Screen Educational Physics

I purchased these RENIAN Polarized Film Sheets specifically for demonstrating cross‑polarisation and residual stress analysis, and they performed exactly as needed. Each sheet arrives protected on both sides, and once the protective layers are removed, the film shows a clear and consistent polarising effect. The adhesive backing is helpful when mounting the film in fixed positions for demonstrations, and the 20×30 cm size provides plenty of working area for setting up optical experiments. For stress analysis, the sheets produce clear birefringence patterns when paired with a second polariser and a suitable light source. Plastic samples placed between the crossed polarisers showed stress fringes with good contrast, making this a very effective low‑cost option for teaching or lab demonstrations. The film cuts cleanly, allowing customised shapes for different setups. Do note that the film must be rotated to find the correct orientation for full extinction, which is expected for this type of work. While some users report receiving mixed adhesive and non‑adhesive sheets, my delivery matched the description. Overall, these sheets are an excellent choice for educational optics, engineering demonstrations, or anyone needing a simple and affordable way to visualise stress patterns in transparent materials.

I damaged the screen on my LCD printer and ordered this by mistake as it clearly says not for 3d printers, I didn`t read the add fully so my fault. So anyway I thought why isn`t it any good for 3d printer? It is a polarising filter just like any other. So I went on You Tube and learnt that you need to orientate a polarising filter over the exposure screen until youi achive the greatest contrast. I did this then backed it up just a few degrees cut the film and placed it flat on my LCD screen did not though glue it. Then carried out a cones of clibration test in grey and it was pretty close to perfect so I printed the landing craft you see in the picture, I dropped it and broke the mast! but it looks pretty good. Now going to try a red translucent resin did a cones test exposure sligntly high so doing a second. However to the point this is not for 3d printers BUT it does and still is working on mine. Elgoo Saturn, why is it working? I do not know but it does seem to be I shall of course order proper printer polariser but at the moment its not broke so am not going to fix it. Pictures show the results. My Saturn is printing really well with a sheet of this fitted I don't know why.

I've used polariser sheets for years but this is first time I've seen or ordered the self-adhesive variant. Depending on your application, this could be really useful, as it applies well to diffuser plastics on lights. Annoyingly, the supplier sent me 2/3 of my order in plain (non-adhesive) variant and just a couple of sheets of peelable self-adhesive. Frankly it's hard to tell apart just looking at it but clearly someone needs to get their stock cupboard or stock codes sorted out! On a positive note, I was glad to be able to try the adhesive material on a real project and would buy it again. If I need self adhesive polarised again, I shall want to know that I am being supplied what I am ordering!

I ordered polerized film in hope to fix my 3d printer after the factor installed polerized film peeled of whilst I was removing an old screen protector when I received the product and installed it onto my printer I tried doing a test print of a 1/12 scale mimban helmet but clearly ad you can see by the photo attached it do anything (if your wondering why the slab of useless resin is so thin compared to what it would look like as a finished print it is because when I noticed I cancelled it).

Like a phone screen, clean peel and stick only it doesn't stick because the glue is on the backing sheet and not the film. It took me several attempts before I realized this, I thought it was because the lenses were slightly curved. You need to buy lens glue to use this. Waste of money

Not film, it is very thick

Product wasn’t adhesive on either side

Good product 👍🏻

Fick detta inte funka

Je l'ai utilisé pour inverser les couleurs de mon compteur de moto et le résultat est super. Avant le fond était gris avec écritures noires (genre vieille calculatrice) et en tournant le film sur le compteur allumé j'ai trouvé le compromis parfait (fond noir avec écritures blanches) du plus bel effet. Ca se coupe très bien et ça colle fort. De plus la livraison s'est faite en 24 heures (incroyable).

Ich bin begeistert von der polarisierenden Folie! Die Qualität ist ausgezeichnet, und die Größe von 20 x 30 cm bietet ausreichend Material für verschiedenste Anwendungen. Besonders toll finde ich, dass sie selbstklebend ist, was die Handhabung enorm erleichtert und vielseitige Einsatzmöglichkeiten bietet. Ich nutze die Folie in Kombination mit dem NinkBox LED Video Licht, das ich ebenfalls kürzlich gekauft habe, und die Ergebnisse sind einfach beeindruckend. Die Folie ergänzt das Licht perfekt, um tolle Effekte und präzise Beleuchtungen zu erzeugen. Gerade für Projekte in Fotografie und Videografie ist dieser Polarisationsfilter ein unverzichtbares Zubehör. Auch für Bildungszwecke, insbesondere in der Physik, bietet diese Folie hervorragende Möglichkeiten, um Phänomene wie Lichtbrechung oder Reflexion anschaulich darzustellen. Sie ist leicht zuzuschneiden, robust und erfüllt absolut ihren Zweck. Insgesamt ein Top-Produkt, das ich uneingeschränkt empfehlen kann – besonders für kreative Köpfe oder diejenigen, die ihre Beleuchtung auf das nächste Level bringen wollen!

Ik wilde het gebruiken om op brilglazen te gebruiken maar je kon ze niet plakken.