AZXYISticky Adhesive Replacement for Windshield Camera Holder, 6pcs 2.76"(70mm) VHB Circle Double-Sided Adhesive Tapes for Dashboard Suction Cup Mount, Mounting Disk Pads, Dash Cam/GPS/Sucker Holder

These work well. Got them due to original suction cups failing(dashcam mount would fall off on hot(90F+) days.Be aware (instructions state this) to NOT touch the adhesive with your fingers or anything else. My first try, I accidentally touched some of the adhesive and guess the oils on my fingers weakened the adhesive and on first hot day, my dashcam mount fell off.Applied another one, this time making sure I did not touch the adhesive and it has held up well.

I bought a dash cam which attached to my windshield by a suction cup. Over and over, I came out to my car to find that the suction cup came loose from the windshield and the camera was just hanging there from the power cable. I got so angry, after this happened a few times that I took the camera and threw it onto the floor of the car. (I don't recommend this by the way). I then found these adhesive labels on Amazon and purchased them. YA-HOO !!! I followed the directions and used one of these labels to attached my camera to the windshield, and it has been solidly attached now for weeks. I am so happy with this product. I highly recommend it.

I have only had these installed for three days now, so I am reserving a five star review for later and will edit if necessary.It comes with absolutely no instructions for use other than what is shown on the sell page on Amazon. I followed the directions and let the pad stick to the suction cup for 24 hours before applying it to the windshield. Then I applied just the suction cup to the windshield and let that sit for 24 hours. It was only after that that I mounted the rest of the phone holder to the suction cup bracket.As of right now the mount is good and solid. I will see if it lasts longer than the five months that the original pad lasted and edit this review as necessary.

We could not get our dash cam to stay on the windshield until we bought these adhesive circles. We trimmed it just a bit to exactly match the size of the suction cup and then stuck the adhesive between the suction cup and the glass. It has not budged since. Problem solved.

My dash cam suction cup unit finally gave out so I had to find other means to adhere the cam on my windshield. During the summer months, the suction cups tend to cause the dash cam to fall off. So I came across this option and decided to try it out. After using these adhesive stickers it seems to do the trick.Tips on how to get a secure adhesion:Make sure you decide on where you want to place your dash cam. Clean the area with some alcohol (70%) to remove any dust, debris and fingerprint oils from the area & wipe suction cup. Apply the (white sticker side) to the suction cup first. (Leave the turn knob open/unlocked. Leave the suction cup flat/natural. I removed the unit from the dash cam before placing the sticker on top of the suction cup/optional). DO NOT TOUCH THE TOP ON EITHER SIDE OF THE ADHESIVE STICKERS, use the sides at all times.. The oils from your fingers will not give a good seal. Give it a good press around the sticker (red side facing up) on on the suction cup. Some dash cam suction cups might be smaller than the stickers. Trim the edges close as possible. (I used an exacto knife.) Remove the red sticker side without touching the center and place the unit where you want it. Press the suction cup unit firmly on the glass/windshield/console panel for about 30 to 60 seconds. And there you have it, a secured dash cam.Side note: Do not turn the suction cup knob on your unit after the sticker has been placed. Air will seep in-between the adhesive and dislodge the cam unit.

Well.....after a day, car parked in a sunny spot, my stickers "melted" and my back up camera "Display" fell off!...the Gray one, that is visible, held, but the clear style melted!...

I bought these because my dash cam kept falling off my windshield. These work for the most part holding it up, but if it gets too hot, the adhesive becomes weak. They’re ok for my purpose but I wouldn’t use them to hold anything heavy.

Wanted this to work, but it did not. I prepped both the glass and the item the adhesive sticker was placed on. I used this on a cell phone holder attached to my windshield. Once I placed the adhesive on the unit and placed the unit on my windshield I waited 3 days before placing me phone on the holder. Today, I placed the phone in the holder and within 10 minutes the weight of the phone (Samsung S10) caused the adhesive sticker to separate from the holder and a few minutes later the other side of the adhesive sticker started to detach from the windshield. I really wanted this to work considering the only problem with my holder was the original sticky part started to melt after being attached to my windshield for 2+years.

after trying different product found this. Good price And works really well