Dual Lock Reclosable Fastener SJ3560 (Clear, 1 in x 10 ft Roll) - Heavy Duty Adhesive Interlocking Tape for Indoor/Outdoor Mounting

Very handy! When compared to VHB tape which works well too, I'd rate this stronger and, less likely to damage painted walls and it has the neat benefit of being translucent. Unlike the black VHB tape, it barely shows up. No need to "hide your crimes" when mounting things to the wall. The same item applying logitudinal angular force on the same surface has now held longer with this compared to VHB tape. Very impressed. I'd recommend using both as they apply to your project. Well priced for 2x rolls. Could do with a piece of tape on the inside of each roll as they unspool easily. Keep them in the box and pull out as required. Cuts easily with kitchen scissors.

This stuff is great! I don't know how they make it lock so tightly when you want but able to be removed so easily if you need at the same time, but it does just that. If you're making a guitar pedal-board, this is THE solution. Previously, I'd used industrial velcro on my guitar pedalboard, but there always seemed to be issues. The wooley side would pick up dander and detritus, the pedals always felt like they had a bit of wiggle to them, and sometimes they would pop off in transit. Furthermore, the adhesive had the tendency to rip off paint and labels and left a residue on the pedals which would affect resale value, so I had to cover the bottoms of the pedals in gaffer tape first which would be fine until I decided to move or swap out a pedal and the gaffer tape would peel off before the velcro came undone. Enter this wonderful stuff! It's pricey but holy hell, does it work. The sticky adhesive is quite strong and I'm confident it will hold onto the pedal, but when you want to remove it, as long as you SLOWLY peel it, it won't damage your pedal or leave any residue. The actual locking part (the 'velcro') "clicks" into place when you press a pedal down to your board with a satisfying "cla-clack". After that, your pedal is ON your board. No wiggle, no popping off in transit. I can actually grab a pedal and lift my entire board with it so that thing is SECURE. When I want to remove a pedal all I need to do is wrap my fingers around the pedal and lift from one side (with a little bit of leverage) and it will pop right off. It's definitely more expensive than velcro, but a little went a long way for me. It seems that the amount you use directly correlates to how firmly it sticks. I put full-width strips across the lanes on my actual board, but then cut strips in half to put at the top and bottom of my pedal (eg, 1" strips were cut into two 1/2" strips and put at the top and bottom of the pedal spanning the entire width). Feel free to use a full strip if you more or less want to lock it in place forever but I like to change things around occasionally. A half-width strip seems like a good balance between holding it firmly while also allowing it to be removed with very little hassle. For my purposes, I have absolutely no worries anything will pop off. I probably WOULDN'T line the entire bottom of the pedal lengthwise like I normally would have with velcro. It's a waste of costly product and a bit overkill, but YMMV. Next, I'm going to experiment with using full size strips to lock my power supply to the bottom of the board. As crazy as it sounds, I'm not at all worried about the powersupply falling off despite hanging from the bottom like that. I'll report back if that ends up being a stupid idea. I know it doesn't make sense that both the adhesive and locking part of the strips both hold firmly AND are able to be removed easily, but give it a try and you'll see what I mean. It kind of reminds me of Newtonian fluid where if you punch it it becomes really firm, but you can easily dip your hand in slowly like it's water. Different tech, I know, but that's the best analogy I can come up with. If you search guitar forums, some people will recommend using a combination of black and clear strips, but I'm almost 100% certain that's just for aesthetics. I used 100% clear strips and it's fine although you can see the strips on the board. If that bothers you, use black on the board. For now, I honestly don't care. Also, if the pedals you're trying to use have rubber bottoms of them, you'll either need to peel that back or better yet, get a flat backing plate from reverb.com, ebay, or perhaps etsy. The adhesive for the strips won't stick to the rubber very well. You could also cover the bottom with gaffer tape and then stick the strips to that, but I wouldn't recommend it for the reasons I'd already mentioned above. I found flat backing plates for the few Boss pedals I have on reverb.com which work swimmingly. Now that I know this stuff exists and how it works, I'm sure I'll find tons of other uses for it in the studio. I can't recommend it enough.

This stuff is seriously strong—way more secure than regular Velcro. Once it snaps together, it really stays put, but you can still pull it apart when needed. Great for mounting things without drilling holes. The adhesive sticks well to clean surfaces, and it feels super durable. Just make sure you line it up right the first time because it’s not easy to reposition. A little pricey, but worth it for how solid it is.

Nothing I have tried (and seriously its a lot) has worked like this. It holds my 15 inch plush cases on to the wall!!! They stay put too its amazing Definitely the best you can get. Strong velcro type effect but way better than actual velcro. Just clean the spot with alcohol, allow it to dry and voila you item stats put mounted to the wall or ceiling. Couldn't be easier and no mounting tape, or anything works half as well

Holds great, as advertised.

This stuff is fantastic. I love using it for everything that calls for traditional Velcro. Even sometimes where 3M exterior adhesive is applicable, I use this, because it's the same thing but with a separation layer. I have two standing desks with Thunderbolt docks, ethernet switches, USB hubs, and all sorts of electronics attached to the underside. This stuff is holding it all together, and very well for a few years now. It's easy to change the setup because of the removability of the stuff. It also doesn't wear out at all, as far as I've noticed. I've even used it at work to affix some heavy vinyl/MDF panels to the wall for aesthetic purposes, which is probably more weight than the 3M Dual-Lock is designed to handle. But it's still there, holding steady, very well. I don't know about weight capacity exactly but it's more than advertised for sure.

Very strong bond with the window frame when used for sunscreens. Though "clear" is not really clear and is more "white" then clear so any overlap from the frame really sticks out.

Very good adhesive. Works well!

Había probado Velcro y otros adhesivos, pero está cinta es excelente, se adhiere con mucha fuerza y cuando se empatan las citas cuesta despegarlas. Si buscas algo parecido al Velcro que pegué excelente está es la mejor opción. (No para telas)

Used regularly for hanging framed canvasses and heavy Artwork - Even use it in my art process - Excellent replacement for nails/screws - Easily installed and removeable from surfaces (using nail-polish remover) - Recommended.

常備品の一つ

Super solide et efficace

Es una buena opción para sostener algunos objetos. En mi caso lo use para luces en una vitrina y también para un imán y si sostuvo correctamente el objeto hasta el momento.