Mudder 28 Pieces 3 Pin LED Connector LED Strip Solderless Light l Shape Lights Extension T Shape Solderless Adapter Connector 10 mm for WS2811 WS2812B SK6812 Strip

just recently finished up my latest PC build and got a set of LED light strips (Amazon ASIN B08GSCJPMD) for accents inside the case. The LED strips were longer than I needed, and I wanted a cleaner install than 12 inches of loose wire at the junctions for that kit. So I got THIS kit of ARGB 3-pin couplers. The short story: These work! I got my LED strips mount around the inside of the window in my case. I recommend using a powered ARGB hub. The long story: Your motherboard probably doesn't put out enough power to properly run a LOT of LED lights off of a single ARGB plug. I ran into a problem when installing my LED light kit and using this couplers kit. The further along I got, the less the LED's worked properly (I did have a 24-cable motherboard extension kit as well). But the LEDs were doing weird things... They would not light up the correct pattern the AURA software was sending, and the LED strips pretty much wouldn't work after the 2nd junction with these couplers. It's as if they weren't getting enough power. And after a couple hours of trying to make it work using different coupler pieces, trying to modify them thinking it was bad connections (based on some other reviews here), I finally came to the conclusion that they just weren't pulling enough power through the motherboard 3-pin ARGB plug - and I have a brand new ASUS Hero VIII mobo! I finally decided to get a powered ARGB hub (Amazon ASIN B08T1SM5CW) as those draw power straight from the power supply and the only control signal from the motherboard. BINGO! Now with the LED strips and LED mobo cable plugged into the hub and powered by the power supply, all the lights worked perfectly as they should! And all the junctions I used this coupler kit for worked great! Overall these worked great for me. I suspect that others that have issues may be running into a POWER issue, not a connectivity issue. I did make sure the click the white covers down very tightly so they stayed closed. These get a recommendation from me.

perfectas para luces led no nesesitas soldar solo picar y poner los pines y empatar y todo buelbe a la normalidad exelente para hacer dobles en las paredes con las piesas muy buena calidad

I run into a few pieces do not keep a constant pressure. This leads to some joints not lighting past that joint. If you push on it a bit they will light. If you mess around with them for awhile they will stay lit. Still easier than joining by soldering wires.

Somewhere along the cabinet project of using these, I ended up soldering the led to the prongs on these connectors. If your LED strip has a flimsy backing, sometimes you have to go in sideways at an angle and not straight into the track or else the led strip crumbles and folds like an accordion.(see first photo) So, to prevent this; if you already have purchased the strip just solder the points, or try to go in at a slight angle and then after put the other corner in after you have the left or right angle started. Other than that pretty decent product! (if you have a issue with lighting dying at a long strip, find the first connector that ends the light on, and see the next one in line is off? That means the 'solderless' contact prong is crooked or not a solid connection anymore, this usually happened to me after sticking it under the cabinet. Hope this helps someone else out)

I bought these to use and every time I attached them to LED strips they would only work about half the time. They wouldn't connect well and all and I would have to bend the 90s weirdly and the LEDs just to hope they made contact. some held decent while others just worked for a second before losing their connection. The plastic clip things just don't work well If you are looking to go around corners with LEDs I would just bend a strip around the corner. Don't buy its a waste of $10

The connectors don’t apply enough pressure and causes it to have a flickering connection if you squeeze it, they will stay on. I had to place a plastic clip around it tightly in order for them to have a stable connection. You get what you pay for I suppose if I choose to get a better connector, I hope these connectors have not damaged it. I am using them on a Govee RGBIC light strip

Works as better than I thought. I attached these directly to my 3 pin led strip and soldered the pins for extra durability. They snap shut tight and hold the strings together well. At a distance you don't even notice them.

These connectors work great. Just cut your LED's at the proper spot, trim off any plastic that might obstruct connection insert and clamp down. They do not inhibit any brightness to your LED's. Great value for the price.

Funktioniert wie es soll. Leichte Handhabung. Empfehlenswert.

Très content de mon achat très pratique merci beaucoup

As others have commented, they are quite tricky to open (I used a penknife blade to pry the catch). Getting the strip light tape in is also difficult (and will be impossible if the protective tape has been removed from the adhesive backing). So, cut your light strip to length and fit it into the corner pieces before removing the protective backing tape. I found a thin bladed spudger very useful for easing the light strip under the contacts, and the strip is held firmly once the catch is closed. After this cut the backing tape close to each connector and remove it to expose the light strip's adhesive back.

Fácil de instalar y cumple su función, perfecto.

Ottimo prodotto