Krylon K02323007 Fusion For Plastic Spray Paint, River Rock, 12 Ounce

If you read and follow the instructions with care, noting the differences between them and what most rattle can paints require, you will learn that degreasing with mineral spirits or the like is a no-no. So do not do that. Do not prime. Do not do anything whatsoever beyond what are in the instructions. AND GIVE PROPER DRY TIMES ON BOTH ENDS. Do NOT respray after it says, or before it says, and ALLOW SEVEN DAYS MINIMUM BEFORE USING PART AT ALL. Seven days is the correct cure time. If you fail in any of these steps it will scratch and peel like you would expect plastic car parts to scrape and peel. If you do your job properly this stuff is FANTASTIC. I am re-doing the color of all my interior plastics in my 2003 Jeep Wrangler with this paint. It should be safe from UV, rain, dirt, gravel, etc. as I did the plastic wheel covers on my 2001 Honda Accord. They have been painted with this stuff (and in regular use) on my car for about seven months now, with no visible damage whatsoever. No blisters, no scrapes, no gouges, no peeling, no discoloration. They look GREAT. The finish is a dull semi-gloss, but they make this paint in a clear that works well and is just as tough.My wheel covers were poorly repainted by the dealership as a part of hiding all the crap in our two-year off-lease Certified, Pre-Owned car. It started to peel right away. Also, it was a brighter silver than the factory paint. When we repainted the 2001 car with a 2013 Civic color (Blue Dyno Pearl 2) the ratty wheel covers looked particularly sad. It was actually rather tragic. I promised myself to buy some nice alloy rims. And then I ran out of money for this project. So I decided to refinish the plastic covers that came on the steelies. (I painted the rims, too, but with a different pant, of course.) The long and the short of it is that I actually like these things now, so what was to be an inexpensive way to get by until alloy rims could be bought have now moved the rims to the "whenever I get to them" type of purchase. The repainted rims and covers came out nice. The color was a brushed nickel, I think. I would have liked it a bit lighter, but the silver was out of stock at the time of my purchase. With the dark blue paint they look pretty good, though, so who really cares? This some excellent plastic paint if you follow the written procedures, which, again, are not like what you may be expecting. Very highly recommended!

My house shutters were terribly faded and needed to be replaced. Figuring that I had nothing to lose, I ordered the Hunter Green Krylon spray paint and my husband and I spent half a day removing, washing, and then painting 6 sets of shutters (two sets were tall, over 6'). It was a surprisingly easy project; the paint was great to work with and provided excellent coverage with two to three light coats. I couldn't be happier with the results and nine months later (with a blisteringly hot summer) they still look perfect. I saved a ton of money by doing this rather than buying new shutters. I purchased 8 cans but only needed 5.

This paint is absolutely fantastic! I finally found a little plastic drawer unit that was almost perfect for my desk except for the colour, light grey. I blasted it with many thin coats of this paint and you'd never know I painted it, the finish looks so good. It really does bond even without any sanding and priming!Here's a tip about the finish: if you want a super lustrous glossy look, follow the instructions and shake the can A LOT. But if, like me, you would be happier with a rougher, more matte, finish, shake the can less.Remember to spray on light coats. They dry to the touch in about 15 minutes, so you can add many coats in one day. It then takes a few hours for the finish to be try enough to really handle, and within a day, it has fully cured if you are in a reasonably dry climate.I love this product so much I ordered more in different colours to paint a bunch of other things around my home.I have added some product pictures to show the before and after.

These are great if...You stick with the darker colors. I thought the Butter Cream would drive me to huff it. The lighter colors are more powdery while the dark more slick. The result is easier coverage and both a better appearance and wear. The lighter shades create a huge cloud of powder which covers you and chips much easier defeating the entire purpose of repainting. My faves are this Navy and the Burgundy. Also good were the OSHA Orange and the school bus Yellow. The White looks very institutional, like nurses shoe's white, and was totally unappealing. I used these paints to repaint a ton of old plastic garden containers. The only ones to end up looking like something cheap from Home Depot were the white ones. We hated them so much on our patio, we donated them to our building to be used elsewhere.Prep the surface! Just b/c it says you don't have to do too much for prep, go online and learn about prepping plastic for painting. The ones I prepped more have fared better. Also, don't expect too much. If you are reckless with them, they will scratch and chip. I was careful and am happy. However, I declined painting the plastic chairs my bldg has on the common patio, something I had planned to do. I do not think these paints, even the darker colors could withstand the abuse a plastic stacker chair endures. So, for something somewhat stationary, you shouldn't have issues.You stick to less expensive colors. The prices fluctuate wildly from $12 for a can of White to $2.50 for a can of Burgundy and are constantly changing. Next month the White could be $3 and the Burgundy, $12. Some of the colors go far and some = 1.5 - 2 cans to get a 20" planter painted. Suddenly your cheap dress-up for a plastic planter costs $25. Add the labor + time and other materials like mask, gloves, drop cloths, it makes more sense to recycle your old ones and buy new. So try to choose cheaper colors especially at first as your learning to use it for maximum coverage etc.So, I do recommend the product if you are willing to go the necessary distance not to be unhappy with the results.

I followed the instructions, but chose to sand for added security.This product performs as delivered- it adheres to plastic beautifully, leaves a soft satin finish, and the coverage is good. I have a BMW z3 with the standard "wood grain" glossy plastic (sorry to any fans of plastic wood grain, but yickkkk!). I also used the clear coat for UV protection as this car is a convertible. I have very little experience with spray paint.Just received the Red Pepper color which I will be using for the center consoles (matches my red car) since satin black performed so well.In areas I didn't get the edges so perfect, I thought I'd be crafty and spray some into a small cop and paint with a tiny brush. Not a great idea, this paint truly must be sprayed to be smooth, not a disaster- but it was a clear texture difference and required I spray another coat. After that additional coat, it was great. The thickness of this paint is just perfect, it will cover light scratches from over buffing. Give yourself the required distance to avoid drip marks.

This was my first time using Krylon Fusion paint and it definitely won't be my last. I used this product to paint my Xbox 360 Slim because it had a few scratches and I wanted to customize it. When properly used and the surface is prepared, the results are amazing.I applied three light coats of paint according to the instructions written on the can and the results you can see for yourself. After one hour, it was okay to touch and there were no runs or cracks. I am going to let it cure for one week so that it becomes chip resistant and maybe add a clear coat for extra protection and a glossy look.I will definitely try the other colors of Krylon Fusion that are available and I would recommend this spray paint to anyone else for all their plastic painting needs.

This is probably the most disappointing product I've experienced in some time. The product was extremely difficult to use. I'm not sure if it's the dispenser tip itself or the paint but it was running everywhere, dripping on everything and it didn't seem to adhere to the plastic shelf I was attempting to cover. It was a mess from the start and the shelves look like a seven year-old painted them. Well, maybe a drunk seven year-old (nothing good can come of that, can it?). I've never had an experience as bad as this with any conventional spray paint before.The irony is that I was really excited to actually try a product that was specifically designed to adhere to plastics better than your average spray paint. Someone really dropped the ball with this product - at least the can I was sent.I usually work with integers in my personal rating scale (-20 to +20). I'd have to give this entire experience a -15. At least it didn't cut off any limbs or spontaneously explode in the process.I will still have to go out and purchase another product to cover what's there now. This was a complete waste of time and energy.

I sprayed a refuse container and was doing nicely until a piece of the sprayer came loose. Then it was spouting drops of paint everywhere. I could not get it back together so it was 80% wasted.Great paint, though.

Paint was perfect job done . thanks

I would say it's good but the paint stripped down after a couple of weeks. You have to sand the plastic to apply this.

Worked great. Covered easily on plastic.

Product once full cured is safe for use inside aquarium.Takes a few coats to achieve full coverage and a flawless finish.

Look like laminated on mdf