BINLUNBINLUN Stainless Steel Watch Bands Quick Release 12mm-24mm Universal Metal Replacement Watch Straps SmartWatch Bracelets Links Straight & Curved Ends Men Women 6 Colors(Silver-Rose Gold,22mm)

This is a wonderful looking watch band. I loved it so much I ordered another. Link removal was not as hard as some said for me. I believe there is a technique to it that I will share in my next review of the band I just purchased. Seller is also incredibly helpful. If you have questions/concerns be sure to contact as they are very supportive and understanding. Can't wait for my next band to arrive and write another review. If I am right about the link technique helping I will try and share that too. Very happy with my purchase!**Edit**I have purchased another band and it is just as great as the first. This time I had a few questions and the seller was prompt and polite when answering them and offered great solutions at no extra cost to me. I definitely endorse this product and seller.For any having issues with removing links/pins some tips-- Line up the pin with the pin removal pin then hold the band in place against the pin removal tool. One side of the pin will be slightly more inset than the other side of the pin, use that side of the band to remove pins and use the slight inset to your advantage by letting the pin removal tool rest inside the inset. Hold the band in place and slowly tighten the pin removal tool by spinning the knob. Keep it lined up as you go. Once it hits the plastic make sure the pin can push through the opening on the other side of the band and just tighten the knob a little more and the pin should just start sliding out. You can then remove the last of the pin with your fingers once it is mostly pushed out. The pins come out pretty quick and easy once you get the hang of it.Hope this makes sense and helps. Happy DIY!!

I bought this to replace the band on my Swiss Army watch my wife gave me 18 years ago. SA does not make a compatible band so I headed to my pal Amazon. This one was closest.Pros: nice design, feels heavy/good quality, looks good vs. Walmart bandsCons: it took me about 1.5 hours to connect it then size it. The tool and parts are great but everything is so small. I'd also recommend a simpler watch band adjustment method - similar to this which is very easy: https://www.amazon.com/16-22mm-Kreisler-Center-Stainless-Silver/dp/B01MXJ0QHH/ref=sr_1_28?keywords=adjustable+watch+band&qid=1558402704&s=gateway&sr=8-28Removing whole links is cumbersome and if you take 1 link off, technically to balance the overall length and wrist position, you need to remove a link on the other side. I may end up between a bit too lose and to tight. Also, the piece for the curved bezel is really cheezy/cheap. See photo - it creates a gap that will catch on clothing etc. so I just went with the straight bezel connector.All this aside, it's only $16 and I was able to keep wearing my favorite watch.

I write this second review because I purchased two watchbands. I bought this stainless band and a black colored watchband with a different review. I had no issue with the service or shipping and everything was included as advertised. However, the band itself was featherweight for being thick stainless steel. The bank looked nice just felt cheap. I had both bands installed by my local jeweler so they could be fitted properly. This band broke after wearing it for two days. I am not hard nor do I abuse a watchband. It just fell off after a link broke. In fact, I did not even feel it fall off, I just noticed my watch was gone and it had fallen between my front drivers seat and the console. I am very lucky that I did not lose a $200.00 Seiko watch. All I can do as a buyer is suggest when you should buy an item and run away when I have bad luck with an item. It is just not worth the trouble to have a problem and then have to seek a refund. So here is where I suggest RUN AWAY and choose another watchband.

Ordered this for my Seiko SNE109 as I have never liked the rubber band. Lug width is 20mm. The lug holes of the SNE109 are drilled all the way through and the wells of the holes are apparently deeper on the insides of the lugs. The spring bars that come with this 20mm band are TOO SMALL and do not stay in the lug holes on this particular watch. They will literally fall out. Measuring the outside measurement of the lug is 25mm. It appears that the end pins of properly sized spring bars will be visible through the holes on the outsides of the lugs. I ordered a kit with multiple sizes of spring bars that will resolve this issue. I did contact the seller and advised him of this issue. I asked if he could send me a couple larger spring bars with no effect. Now I will have enough spring bars to rain down on the entire world.Update 4-22-2020: Received the spring bar multi-sized kit. I found that 25mm bars were too large. In the end, it was the 22mm bars that worked. The ends of each bar are just visible in the outside lug holes. If amazon lets me I will post a pic of the bracelet installed. In order to install the curved ends, the first link on both end must be removed. I had to remove 3 additional links to size it, which was no issue with the pin pusher that comes with the bracelet. The watch looks far better with the new bracelet.

I got this as a spare for my Carnival Tritium Watch, 40mm case model. It requires a 20mm band. That watch comes with a curved end band. Except for the ends that attach to the watch, it is identical to the original Carnival band. This band fits ok with the straight end if you don't mind the look. It doesn't look too bad, but I like the curved ends better. The supplied curved ends do not fit this watch, the pins do not line up. They do line up with other watches I have but not the Carnival. The good news is that the inner segments are the same width as the original Carnival band. This means that you can take the straight end off and use the Carnival curved end pieces. For my 20mm band, the inner links measure 10.85mm wide. They fit into an 11mm gap.The band is good quality and has good weight to it. The clasp is the same style as the Carnival.The link tools are decent for occasional use. If you are not good with small mechanics, go to a jeweler. You still need some skill to make it happen.

The pins on one side of the watch have a little slot on the end, looking like a little screw (but it's not). The other side doesn't. You push from the side without the slot. I only found this out after cocking it up and looking at a youtube video. You also need good eyesight and high contrast light to see "the slots". I did everything wrong in shortening and fitting the bracelet, taking about four different attempts at all the processes but, despite all this abuse, the bracelet was perfect still, once finally fitted. Good points:The clips to release the bracelet, no lumpy big metal tabs.The choice of straight or curved ends where it connects to the watch. If they fit, the curved ends seem to really make the look of the watch case where it connects to the bracelet.The pin pushing gizmo, although the pin part is a little weak. Make sure the bracelet is straight onto it or you'll bend the pin.Brushed and polished bracelet. Using a loupe, it looks really well finished.My watch had a leather strap but the bracelet has transformed the look of the watch face and I don't know why. It may simply be the bracelet added a bit of bling to the watch!

It arrived very quickly but there was damaged slightly to the package but on opening it the product was not damaged.I was happy with the value of the item and it's extras the strap and pin extractor all in with the strap as I had purchased an extractor on its own before and had to return it as it would not do the job and that alone with postage cost £11So looking at that getting the metal strap and the tool to remove links was a bargain and it worked without any problems and the pins did not bend up like the last extractor I bought.The strap fitted my with no problems to my Casio 22mm lug on the watch and the old strap removed and the new metal gold one fitted in less than 2 minutes.Very happy with purchase and would recommend

It is not easy to find metal watch straps and having trialled and errored a few these are really great. The sizes are exactly as described and they have the same width throughout - they don't taper. I bought two: silver and silver with gold for two old watches. I have just ordered a third silver with rose gold for another watch. They fit perfectly, the tools are easy to use and the links easy to remove. I am extremely pleased with the results. The clasp is very nice too. The watches look great. I have not had them for long but they seem to be good quality and robust. The next day delivery service was prompt too.

Amazon sent this in a massive box at least 20 times the strap size. Unbelievable!The strap itself is good. Well made. Fairly easy to take sections out to adjust to wrist using tool provided. Intially used the curved links to connect actual watch to strap. Oh so fiddley and difficult to connect. Then one side unhitched itself. Decided best option was to not use the curved links. The straight link to the watch so much easier with its quick on & off pin. It looks just as good. The quick release pin allows you also to change straps very quickly. But for the wasted time trying to fit the curved edges and for it to then disengage nearly losing the watch, I would have given 5 star.

Excellent replacement strap that has the look for a very reasonable price.Pros - looks expensive, nicely polished with a stainless butterfly type centre closure which does not snag or catch on clothing, straight or curved ends to fit watch shape, extras to maintain and fit bracelet.Cons - lightly plated (only time will tell how quickly it wears off) quite light in weight - could be heavier, thin curved ends had to be opened wider to fit the watch neatly.Overall 4/5 and would buy again.