LP103395

This seems OK so far. WARNING: DO check the POLARITY of any device that you connect this (and other LiPos) to. I needed to reverse the red/black wires in the connector for my purposes. This isn't a defect of the battery, it's purely a matter of understanding what you're connecting it to - irrespective of whether that be a device or a charger!

Good quality 3700mAh battery but be mindful of the polarity of your application, as clearly stated by the manufacturer. These appeared to have a JST connector who's polarity is typically found in Radio Controlled toy world; the Internet of Things seems to use the opposite (i.e. there is no "standard" for polarity on these type of connectors) If you're very careful it's possible to poke out the metal conductors from the plastic housing of the JST connector and reinsert the desired way around.

I am currently amusing myself making portable audio equipment. The main concern with Lithium battery power is safety. This battery has battery protection built in. I can use it with cheap chargers and with cheap and poorly specified Bluetooth modules and class D amps with confidence that abuse cannot be catastrophic. It also has a handsom capacity. My diy Bluetooth amp lasts ages using it 3.7Ahrs! I must add a further caution for users after having read other comments. Li batteries are dangerous when charged incorrectly particularly when overcharged. This one has a protection circuit built-in. However, I would say that it should not be charged directly from the likes of phone or other plugin usb power supplies. Use one of the many cheap charger boards available that will automatically reduce the charge current near full charge and shut off charging when the voltage reaches 4.2v. the battery will also last longer and be safer if the charge current is limited to 1/3rd of capacity or less. No more that about 1A to 1.2A. This increases charge time but is safer and less fatiguing on batter life. Some usb supplies only limit at 2A or even 3A and have no shut down. Be cautious!

Bought to experiment with RasPi zero, pico etc with suitable power adapters. It needs to have the polarity of the connector changed to match the needs of the boards. Some careful work with a very small screwdriver to ease the connectors out of the housing and swap over.

Ok but ordered wrong one again,but good seller and product

Used to replace a battery in a radio which had stopped holding a charge. Came well packaged, connector was as described. Works great

Had to swap the connector polarity, it's annoying that there is no standardisation

Before you plug this into a charger or device make sure the cable plus/minus <> red/black is the right way round, it is not a manufacture fault for your error when you're warned that you need to make sure that the cables are the right way round in the plug for your device seeing a few one-star reviews when it was their own fault that they destroyed their device or charger because they didn't check the red/black was correct for there device,, the plug or device socket has no standard +/- layout

I got this for an airsoft pistol and learned that said pistol needed higher voltage to run properly. Said pistol uses a faux extended magazine to house the battery, and this one was a reasonable fit. I'm a bit disappointed it didn't work out, but I have plans for this battery. I own and operate some 3D printers as a hobby and this battery will work great for a few LED lamp projects I have in mind, but I digress. I appreciate the fact that this battery has a built in low voltage cutoff, though I have no intention of testing it. I see a lot of folks use this for microcontroller applications though I can't comment on this battery's efficacy there. For test running LEDs with a buck converter, this battery is working great, it has a much higher capacity compared to the numerous tiny single cell Lithium batteries I have laying around, yet it's compact enough to fit in portable lights. As for the battery connector, I again can't comment. I removed the molex connector that came with this battery and soldered a Deans connector onto it's leads (after testing it on my programmable charger with the molex connector on) and I haven't had any issues. I'm very pleased with this battery, and should I ever need one like this for a future project, I'll gladly order another one.

Bluetoothスピーカーのバッテリー容量が少ない為、こちらのバッテリーに交換しました。 大変満足です。

Ik ben tevreden met de snelle levering van de accu's, alleen bij mij zijn niet helemaal oke. De accu's willen niet fatsoenlijk laden, en zijn naar mijn idee zeer snel leeg.

La compré para sustituir otra batería dañada de una linterna…Funciona correctamente

I've used these with a DIY camera and they work great!