TEKTON 3/8 Inch I.D. x 10 Foot Rubber Lead-In Air Hose (250 PSI) | 46334 | Made in USA

I just plumbed my garage using all copper and 1/2 NPT fittings with 5 drops and 2 hose reels with a condensate trap at each drop with ball valve drip legs and quick connect fittings for air. I needed 3 of these 3 foot by 1/2 NPT fittings at each end lead ins to complete the project by connecting the compressor to the system and the system to 2 hose reels. Some pipe thread sealer and these lead ins did the trick. So far they work perfectly and do not leak. I have the system set to 100 psi and it is always on. They are flexible and well made. Only time will tell how long they last.

Bought this to use as a leader hose from my air compressor to my air filters. I was using a 3ft whip hose but it wasn't long enough to cool the air down before reaching the filters. The 10ft hose is a lot better and has worked well. It is a nicely built flexible hose that is almost as good of quality as my good year hose. On review shows a swivel end on his but mine came with 2 regular type ends that fit 1/4" not fittings.

Bought this hose for the small project and worked well. It was few years back and still holds well.

Used the hose to test it for leaks. . its connected to my 150 PSI air tank .I ran a test on the hose by pumping up two completely flat tires . each tire took 35 lbs. it pumped both up in about a minute and a half . (of course that depends on how much air pressure you tank has ). I'm pleased right now with the hose but in fairness I haven't used it enough to give an accurate review. that's why the 4 stars . all the fittings attached easy the hose is easy to handle. so far so good .

I originally purchased this hose in October 2016. I am writing this review January 2020. This air hose is great quality, very flexible rubber and feels heavy duty. I also like the extra support where the fittings are attached. I have had no leaks or any other issues from this hose in the more than three years that I have owned it. As a matter of fact I am going to order a longer version of this now.

I have had this hose installed for several years now. It's a good quality hose and heavy duty fittings. I use this to run a small sand blast cabinet, and I have probably well over 200-hrs of sandblasting time. This hose whip allows me to pull the cabinet away from the wall to clean or do maintenance behind the cabinet. This really feels like an industrial hose. It's very good quality.

This installed easily as a lead in hose from my air compressor to the reel. It does not have rotating end so if you directly attach it to the compressor and not use a quick disconnect, on one end you will have to counter rotate the hose as many turns counter clockwise as you think it will be turning clockwise, if you don't there will be a kink in the hose. If your off a twist or two you can just turn the compressor around and your good. Sounds complex, sorry about that, but this hose is very flexible and soft. It fit tight and had no leaks as I used thread tape.

This one should last. Purchased another brand several years ago which suddenly got soft in one spot and burst. This left my compressor motor running all do long without me knowing. I'll make sure I turn the valve off from now on, but I shouldn't have any problems with this one. Very heavy and fills like it will last forever with my pressures.

As advertised. This is the 3rd tekton I have used (all different lengths) in my jeep YJ OBA. They work, they're tough. One suggestion might be to be a loose spinning head tightener on it. But other than that, I've had no complaints, 3 years and running while abused

ok

Nice quality hose and end fittings. Unfortunately I didn't pay enough attention to the fact that it's of US manufacture so was most likely to have NPT threads, not BSP as more commonly used in the UK. It's also mentioned in the description that the threads are MPT/NPT (same thing, M simply specifies that it's a male NPT) but I somehow managed to ignore that too. So, for any other shoppers who pay more attention to the reviews than the item description, let me reiterate that if you're hoping to connect this to BSP fittings, it's not a direct fit, you'll need NPT/BSP adaptors. For some inexplicable reason those are very expensive in this country, so I opted to cut off the ends and fit barbed connectors instead. If you want to do the same, you'll need 3/8" or 9.5/10mm diameter barbs. Five stars from me for the quality, I won't mark it down on account of me failing to read the description properly!

Okay

no issues with item