SimbaLux Acrylic Sheet White 32% Translucent Cast 12”x12” 1/8” Thick 2 Pack | Square Panel, 3mm Thick, Plastic Plexi Glass Board with Protective Paper for Signs, DIY Display Projects, Craft

Nice piece used to block off gap in 2 new appliances

TLDR: Good quality, easy to cut, easy to remove paper. These came in and right away I was impressed by the quality. Even though they were 1/8in thick they were quite strong. I used them to replace the metal racks in my mini fridge and they work perfectly. I had to cut them to size using a miter saw. The sheets cut cleanly for the most part. 2 of the corners chipped off but for my purpose they worked. The protective adhesive paper come off very easily if you go slow and work with the paper, not against. The last picture shows one of the sheets which slipped under the guard on my saw while cutting. I suggest putting material under the sheets if you have a 1/8in gap on your saw. I believe this mishap was due to my saw and my skills with the saw, not the material itself. Make sure you wear protective pear while cutting as there is a ton of byproduct. Would purchase again.

Exactly what I needed. Right color. Easy to cut with acrylic knife.

The Plexiglass itself is fine. However, the adhesive backing was really difficult to remove. It should have full tabs and something to make it easier to peel. I had to deal with finding a spot to pull from (and breaking a nail in the process) and then it didn't pull off in one piece. I had to peel off several pieces from both sides.

Purchased these panels for laser cutting/engraving, to use in LED night lights (base lights sold separately, of course). The acrylic cut beautifully, using settings found online as starting points. Resulting images were clean and good quality. There is protective paper on both sides of the panels. Left this in place during cutting (to protect cut edges from possible scorching) and peeled off the uncut areas of paper afterward. Larger areas of backing peeled off easily by hand, then cleaned up small areas of paper backing using a light duty (** non-scratching! **) Scotchbrite / O-Cel-O type sponge under warm running water. Paper peeled right off, leaving an unscratched surface and some really nice, custom made gifts. The images shown are about 7 inches high, and demonstrates how the led lights up the image. Note on the owl image that the edge is a little rough, resulting from my software trying to cut around the owl more than once. My fault in how I imported the image, not the fault of the acrylic panel. The others were nice and smooth after a single pass.

Worked well on my laser for both cutting and engraving. No issues with cutting or engraving. Came out smooth and looks professional.

Just what I wanted. Good product. Would buy again. The cowboy

I used them to build an extension to a mini wall to keep our cats from jumping off of it and breaking things down below. The extension looks great and doesn’t block our view. The panels are so clear that they’re barely noticed. Also, they are straight and not warped. One small caveat is that one piece had a couple of very minor nicks on it, but they’re not noticeable unless I search. Also, when cleaning them, it needs to be done gently because it looks like they may get scratch marks over time. The quality is great, and each panel came with protective adhesive on both sides, and wrapped in bubble wrap inside of a fitted box. My only complaint is that each panel came in a separately shipped box about 16x20...they fit in at an angle, so I’m guessing there wasn’t a big enough box to hold them. But, that part seemed pretty wasteful.

Sheet is good

Low quality acrylic

very good helped me out

A bit expensive as it was imported. I probably would have found a piece cheaper if I'd got off my butt and visited 3 or 4 stores but hey, that's what Amazon is so great for! I used it as a see through roof on a hedgehog feeder that I've set up. I've designed several over the years but my latest is a wire cloche with this see through roof and a piece of 5" tube jutting out of a hole I cut and lined with silicon oven shelf protector. Yeah, I guess a photo is required really!

Not as the picture , ita not a black acrylic .. its transparent