Replacement for 2 New Uncut Transponder Ignition Car Key for Select Toyota Vehicles TOY44D-PT

I bought this to replace a lost key for my 2006 Toyota Sienna. Going through a dealership would be much more expensive. Some local locksmiths were quoting a higher price for a replacement car key as well. Took it to Home Depot, got it cut, and then programmed it myself. Saved a bunch of money. The programming instructions I found online took a few tries to get it right. These are the ones that worked for me: 1. Sit in your van with all doors closed. I opened and closed the door one time to 'clear' the system. 2. Insert your original master key to key cylinder 5 times and leave it there ('in' and 'out' four times, just 'in' the fifth time). 3. Open and close driver side door 6 times. Should be closed when you do the next step. 4. Remove master key from key cylinder, and within 5 seconds insert your new cut transponder key. (NOTE: the original instructions I found said to then turn the new key to the ON position, but that didn't work for me. Someone suggested completing the steps without turning to ON and that worked for them, tried it and it worked for me too.) 5. Look at that red engine immobilizer light (the red light to the left of the speedometer which is car shaped with a black key in the middle of it). It is solid indicating it's in programming mode. After inserting the new key it will begin blinking. Wait about 1 min up to 90 seconds and it will turn off by itself. 6. After engine immobilizer light turns off, remove new key and insert original master key. Start engine. 7. Now try your DIYed new transponder key to start your Sienna. Obviously different models or different years of Sienna the programming instructions may vary. And even doing the same steps it took a few tries before it worked for me. But hey, way cheaper to do it myself!

Exactly what I needed for my 06 Tacoma! Buy these and have a locksmith cut and program them and you will save Alot of $ over getting your dealer to make new keys!

Decently made good price works perfectly with my 2008 tundra but needs a programmer to work IF you have that or take to a locksmith it works good most big box stores with the computer key cutters won't cut and program this key though. those machines are set to program only there brand of key. if you find a little hardware store with the older machine or the old vice cutter and someone who knows what there doing you can get it cut just fine and program it yourself.

Good Keys and programmable. However make sure you buy the right keys for your vehicle. These did work for me but I knew what I was buying.

Works great for my 2004 Sienna. Programming the key took me a couple of tries following the online step by step process. Doing this yourself can save you $$.

We had two transponder keys cut for our 2005 Toyota Sequoia at a local locksmith for $10 total. This is the procedure we used to program our keys on 12-31-2024. There are lots of suggestions on the way to do it, and this is what worked for us. Delete Keys: When we began, we deleted all keys except for the one used for the deletion procedure. One of our keys got lost in a school parking lot so we wanted to delete it from the vehicle. It is said that the vehicle memory can store 4 Master keys and 2 Valet keys. We now have 4 programmed Master keys and 0 Valet keys. 1) Close all doors 2) Insert your Master key (black) into the key cylinder 3) Turn the ignition from LOCK to ON 6 times within 15 seconds - on the 6th time, leave the key in the LOCK position 4) Open and close the driver's door 7 times within 20 seconds 5) Remove the Master key 6) Open then Close the driver's door to end the process Add Keys: 1) Close all doors 2) Insert your Master key (black) into the key cylinder 3) Turn the ignition from LOCK to ON 5 times within 15 seconds - on the 5th time, leave the key in the LOCK position (Others have suggested leaving it in ON but that did not work for us.) 4) Open and close the driver's door 6 times within 20 seconds 5) Remove the Master key 6) Insert the new blank key and turn to ON position 7) Leave in ON position for at least 60 seconds (Our Immobilizer light did not blink during registration mode, nor did it turn on or give us any indication when a key registered. We left each key in for 120 seconds and all keys worked.) 8) After 60+ seconds, remove the key 9) Open then Close the driver's door to end the process 10) Test the key to make sure it works. One of our keys hesitated to start the vehicle and it did not start. We started the vehicle with the Master key and then again with the new key and it has worked multiple times since then.

2005 Camry XLE. Okay, I tried both ways to program these. I tried both keys. The same error code blinking always. 2 short then 1. I tried programming them with the Tom's Keys TSL-2 and using the door slam method. No joy. Too many keys is NOT an issue. I cleared all prior keys so the computer reads 1 Master, no Valet. That code has to mean no chip. Or, it's the wrong chip in a Dot stamped key. Either way WORTHLESS! Now I am outside the return window, so I have to eat this one. Don't waste your time and Amazon's money, doing returns. Buy from Tom's Keys or Keyless-Remotes. Little more money; a lot less hassle!

Amazing! Their website had proper details to make keys work programming them in my 2008 4runner. It was a bit finicky, but eventually everything coded and works. Saved a LOT of money setting 3 replacements with proper coding.

Did not match frequency of the car

Both keys work but I had a heck of a time trying to find a place to get the keys cut. None of the big box stores would touch them (Walmart and Home Depot) ... they started making up stuff like "its illegal". I contacted a lock smith and he wanted $130 a key to cut them (????) and that was without programming them. In the final analysis I got them cut at a shoemakers shop .It took him a couple of tries to get it just right (I think he was bing overly cautious) but they work perfectly (he charged $5 per key). As for programming the keys, that wasn't an issue. The instructions are easy to find on the internet (steps like ... open door, close door, try key remove key etc etc etc). Both keys programmed on the first attempt.

Didn’t want to get ripped off by the shop to get duplicate security keys for my car. Got the right security key blanks and you can self program these keys in your own Toyota - depending on the model the method may differ. Saved myself $60 per key!

These key blanks were just what I need3d for my 2004 Toyota Sienna. All I had to do was get them cut, and like magic, they were able to be paired up with my van without any issue.

I had to go to a locksmith to program it. They were willing to cut it for free.