Xprite Tow Hitch Compatible with 2018-2025 Jeep Wrangler JL JLU 2 Door & 4 Door, 2" Inch Trailer Hitch Receiver with Cover

I have a 2024 Jeep Wrangler sport. This tow hitch fit on so easily, I did not have to remove the muffler or anything. It took me about 15 minutes to put it on and it's super sturdy.

Purchased to be able to take our electric bikes with us when we travel and works great very easy install on our 2021 Wrangler all holes lined up perfectly.

The instructions are tiny and difficult to see, but it's such a straightforward installation you won't really need them. We installed the bolts holding the hitch in the frame opposite the instructions to avoid needing to remove the bumper. To help get the nuts on in the tight space between the frame and the bumper, we put a piece of tape on one side of an open ended wrench to help hold the nut in the wrench. Then, once the threads caught we just tightened it down with a torque wrench on the muffler side. You can tell a good engineer designed this hitch as they called out Nyloc nuts on the frame bolts. These nuts are ideal for high vibration applications as they won't entirely back off if they get loose. One other thing to note, there is a little notch in the electrical plug that mounts on the hitch. You want to orient the electrical plug properly so that the notch holds the plug in the hitch. It was opposite the way we intuitively thought it should go, so pay attention to the notch.

I've had this hitch installed for about 2 weeks and it's worked well for hauling bikes on a hitch-mounted rack. I do have plans to tow with it soon.Install was pretty easy, but because I had an aftermarket bumper, I did not want to remove it (heavy AEV rear bumper). I was able to slide the bolts in from the muffler side and hold the nut (taped) on a closed end wrench between the bumper and frame. That worked well, and was much easier than removing the bumper.No instructions were included on how to do the electrical, but a simple YouTube search showed how the harness works. Other kits had little plastic knobs on the wiring harness to allow for easier routing/attaching of the wiring along the frame. This one did not, but a few zipties did the job. I would have liked to see higher grade bolts included. I might swap those out at some point.

The hitch is sturdy and painted well. Just slide over crossmember and install the 4 provided bolts into the crossmember holes (comes with them from the factory), tighten to 80 ft pounds and done. Received product in 2 days from this vendor.

Easy to install. All of the parts lined up with the existing holes already on my vehicle frame. I have a 2021 Jeep Wrangler. I use it for a 3-bike-rack and it works fine. There was some wobble so I ended up buying a hitch stabilizer for under $20 that fixed that. I assume the wobble was from my bike rack design not the hitch itself. The dealer wanted to charge me around $1000 to get a Jeep with a hitch option. This saved me over $900!

ordered this item to tow trailer behind my Jeep. Installed it on the Jeep and several days later I attempted to put the 2-inch hitch into the receiver. Receiver was extremely tight and was unable to put hitch in far enough to put the pin in the hitch. After looking at the receiver I found that the collar had been welded crooked, and it was approximately 1/8 of an inch off causing the hitch not to go into the receiver. Notified Amazon and sent it back and they sent me a replacement receiver, Received the receiver today and once again hitch would not go into the receiver and once again the collar on the receiver was off approx. 1/8th of an inch. Notified Amazon again and will get a refund on the receiver.

Installed this hitch on my 2018 Jeep Rubicon Recon. Fit great and easy to install, about 20-30 minutes taking your time. I’m sure others could install faster.