HandAll Beavertail Rubber Grip for Glock 17, 19X, 22, 45

Installed on a glock 17 gen1. Grip feels perfect now. Huge improvement in feel an I now have my beloved finger grooves. I had no trouble at all installing the grip. I placed it in boiling water for like 3 minutes, removed and stretched out the rubber ALOT. Sprayed the guns grip and the Hogue grip with window cleaner and she went right on. Took maybe 1 minute. Was not hard to do at all. Granted I have good hand strength so it was easy for me. I can see how it would be difficult for alot of people.

Just what I expected with Hogue. I have a grip for my Beretta 92FS which is much easier to put on as it has removable factory grips, just swap em out. This grip has to be slid on, which made me hesitate, wasn't sure it'd meet my expectations. It's nowhere near as hard to slide it on as I was led to believe by the instructions it came with and AI! Heat it in boiling water, never gets too hot to touch being rubber, spray Windex inside the grip and with your hands stretch it over the bottom of the grip, pulling to stretch the opening bigger as you go. Once you get it fully started, it's easy to just twist and push it up the grip. Once fully on, twist to align the rear seam with the guns centerlines on the back of the grip. The Windex will dry out in a few hours and it will no longer twist easily. Fits perfectly on my Glock 21 Gen 5 and feels awesome as you'd expect from a Hogue grip!

So for the price this is an amazing item. I am 6'3" and have corresponding sized hands. My 9mm Glock 45 fits my hands well, but I still wanted a little more grip. This was the perfect solution. Grip feels much more solid and controlled. Installation is not easy at all. But if you work smarter you won't need to work harder. I used the boiling water and windex route. First, pour boiling water into a bowl and let the grip soak in it for 30+ seconds. While it is soaking spray the grip with Windex and don't be stingy, it should be dripping off. I installed it with the slide removed. Using tongs pull the grip out of the water, shake loose any residual moisture, and install as quickly as possible. I did not need to use the two plastic strips that they suggest, but it did take a few attempts to get the first part of the Hogue grip over the Glock grip. Once the first part is attached quickly slide it up using any means you can. The windex gets super slippery so I kept a towel nearby to dry off my hands during the process. I also re-dipped the Hogue into the hot water during the process. The trick is to be prepared and to move quickly but efficiently. Heat and windex are your friends in this. Be patient and deliberate and the install won't be easy, but will be possible.

Fits Glock 20V Gen 5, don't listen to everyone else!! The packaging doesn't list it, but if you look up Houge item #17020 you will find it listed as working for the Glock 20. It fits per the picture. Wasn't easy to get on, but I didn't need to boil it or use Windex, just muscle. Haven't tried it with the grip yet but hopefully it will take that tiny sting off the 625lb loads...

I had purchased a G22 police trade-in, and while it was in great shape overall, one side of the grip was “chewed” up. Likely caused by seatbelt rub, which is understandable. This hogue grip was perfect for covering all of the damage. However, it was a BEAST to install. This thing fits tight, and is no joke. I admit I didn’t use the “shoe horn” style recommended on the instructions. Nor did I use any liquid or lubrication, because I didn’t want any trapped between the grip and frame. I used a blow dryer to intermittently heat the grip and make it more pliable, as I worked it onto the frame. Took me about 10 minutes. But it was tough to get installed, so following the instructions is probably the better route to take (which should be obvious, but...you know). After being installed, I am happy with the feeling of it and the grip overall. The grip does push my finger up into the trigger guard a bit, and I’m guessing “Glock Knuckle” will be exasperated by this grip. But there are work arounds for that too. So overall, I am happy with the grip....especially because of the damage it covered. 4/5 stars for me. And I would recommend, it’s a quality product ******************************* I rely heavily on reviews when I make purchases so I put some time into reviewing everything I buy on Amazon for personal or business use so I can help other people considering that item. If you found my review helpful, please consider hitting the "helpful" button below when it asks if the review is helpful!

Fit block 19x perfectly. Very nice grip.

I absolutely love this grip on my Glock 43X. I recommend heating it with a hair dryer to help with application.

I have a Ruger RXM with the full size grip modual. The Hogue HandAll Beavertail Grip sleeve for the Glock 17 fits perfectly. This is the fifth Houge Grip Sleeve that I've bought. I heated it up with my wife's blow drier and it went on MUCH easier than I expected. I highly recommend it.

G17gen5へ装着予定でしたが、私のやり方が悪いのか全然入りません！

Excellent

Lors de la commande j'attendais vraiment un pistolet a air comprimé , et le résultat de la commande est seulement la poigné de l'arme ( pas très explicite) .

Love it! Fit perfect and feels very nice in the hand.

Nice grip