Bgears b-Voguish Gaming PC Case with Tempered Glass panels, USB3.0, Support E-ATX, ATX, mATX, ITX. (Fans are sold separately)

It doesn't come with fans ,but for the price it is still well worth the money. A comparable tower would cost at least 25% more. Tempered glass and metal. Bottom where PSU goes has a cover. Inside is designed for great cable management with space in back for excess wiring and a lot of openings for all the connections. Leaves a very clean look once build is done. Has good airflow and plenty of room for ATX mobo and full size GPU,PSU. Very sturdy and would make any build look good. Easy to work with. I put three fans in the front, one in the back. Core i5 and RTX 2070,600 w PSU, works great and temps are real good.

I got this case purely based on aesthetics. I had no goals for performance and didn't even consider how hard it would be to setup.I have the case fully set up with my new Ryzen 5 3600 + 1660 Super + a fan for literally every spot in the case. It was a true JOY to work with. It's beautiful looking and even my wife who thinks this stuff is stupid said "wow that is a nice looking computer". I have no regrets and would absolutely buy it again. It was so easy to set everything up and it holds very decent temps.If I was to mention ONE bit of a feedback? I'd say the front panel should be an additional 2mm away from the case to give a liiiittttle extra air flow on the front intakes but even that isn't an issue really. I used a Cooler Master 212 RGB Black Edition cooler and my temps average between 50-60 C while gaming and it RARELY hits higher than that. So maybe if you're running a stock cooler you might have some higher temps but even when I had the stock Ryzen cooler I wasn't exceeding 75 C very often (literally peaked at 79 once and that was while running a stress test and that was the stock cooler which isn't great in any PC case)If you're on a budget and want an r/battlestations worthy case - this is it.

For the price I cannot imagine beating this. Very sturdy case and looks extremely pleasing to the eye, especially at the price point. I have a slightly more expensive case for my gaming PC (this is for my nephew) and I think this might be better, especially because of all the wiring slots for initial wiring. There are grommets and slots all around the motherboard's spot so sending wires in any direction is very simple and convenient with a clean finished look. The tempered glass panel is very pleasing to the eye and has a clever method of attachment (two swivel hinges that come up and two cushioned screws) they even provided a WAY overabundance of extra specialty and regular screws you might end up needing! I will be looking back at this company if I ever need another case.

Large and spacious inside. Full Glass door and front! WOW! This baby is awesome. My full size ATX and ATX Extended MOBOs fit in this puppy with lots of room for my huge graphics card, dual fan water CPU water cooler and 4-RAM modules. With the power supply & drive bays hidden underneath the interior space, there's plenty of room to mod your PC without concerns for space. There are no drives to block airfolow and wiring is completely hidden below or behind the MOBO..The GLASS is thick and heavy, so bumping it won't break it. The side door can also be removed completely for full interior access for major mod work. With the front and side being mostly glass, you're allowed to show off your PCs guts and true coolness! The included RGB fans are huge 140mm's and push air in, beautifully. When everything is all lit up, the color takes over in a blackened room for cool FX..The underside, holds and hides your power supply and all interior drives, whether 3.5" or SSD, there's room for them to live comfortably. The front fans cool the underside as well as the upper interior. With 3-fans in the front, you get lots of airflow. The top allows for 2-3 exhaust fans, and the back accepts a 120mm fan to blow hot air out the back as well. This is referred to as "positive-negative" flow balance. 3-in, 3-out. Well-designed for functionality and, well, just showing off!

I have to say that the tower is amazing for $70. The add however is deceiving and I am a little disappointed with that. Yes, this is my fault for not digging deeper into the questions and answers section. It does not say anything about the rgb fans not being included with the tower except in small print in one of the pictures and in the Q&A. So I ordered them separately. That little bit aside, I am very happy with the look and functionality it. There are far more places to rout your wiring than I could ever need. I used 5 of the uphere 140mm rgb fans for the front and top and 4 of the uphere 120mm rgb fans for the bottom and back of the tower. It looks clean and amazing. If you have the cash I would go for it.

This is the second time Ive bought this case.First one was amazing for price.Secind one was bad. Missing all its hardware, it was used the motherboard standoffs were missing all except two of them.The peel away plasctic was crumpeled up and reattached.Obviously used before... but the box it came in was new, with new tape untampered. They threw a used case in a new box without the hardware, slapped a 10% discount on it and said it was new.... thats pretty shady. If i didnt need a matching case I would go with another brand case. Hoping tge third times the charm... Moms new PC will have to wait until after Mothers day now.

Tempered glass side and front, (the front comes off easy to install fans, at least it did for me. Then it fits snugly back in place.) I am so very pleased with this tower! My Motherboard fit right in and this case is not cheaply made in any way. I spent a lot through another vendor for my other full sized tower and got yucky plastic sides... so this one is a real step up. All of my components fit in well, it looks sleek and really beautiful! If I ever resell this PC it will sell itself! I don't think I will be parting with it so soon though... :) The LED components look really nice reflecting out through the glass too. Really snazzy while also looking neat and tidy.

So I don't like that it doesn't come with any fans. I was surprised when I opened it up and found none. I went back and read the entire Amazon listing and did find in the question section someone asked if it came with fans and the answer was NO, but the listing sure does not make that clear and makes it look like it does in the pictures. In retrospect, I think it probably makes more sense for them not too because you really need specialty fans to get the best cooling here, and if they'd added those, the price would have been significantly higher. I explain below.As to the people saying their hardware gets hot, I suspect the main difference is what you are running and the type of fans you have. If you are running a brand new micro-atx motherboard/cpu and a big GPU, you aren't likely to see a big heat issue if you tune and face all your fans CORRECTLY. I would suggest however 3 - HIGH PRESSURE 140mm fans for the 3 front intake fans because the glass front obstructs direct airflow to them. High pressure fans will pull more air through the slits between the glass front and the case than a standard fan will. A standard fan will flow more air, but they can't pull or push air well against restrictions. The difference in the fan is just the blade width. The wider the fan blade, the higher the pressure the fan can transmit. I use Fractal High pressure fans.I specifically bought this case for its E-ATX capabilities. I am running a dual CPU server/workstation motherboard, and I can attest that this thing definitely heats up quickly with this setup. For this price point and case size, I can live with managing the heat situation, but its certainly not exceptional for a case. The biggest issue I have faced and its worth noting is that if you are running an E-ATX board, the TOP COOLING FANS WILL BE PARTIALLY OBSTRUCTED. This means you will need to purchase slim 15mm thick fans (120mm or 140mm) if you want to use the the top fan mounts. There are not very many choices here, and mostly they are not cheap.The design is otherwise simple but elegant. I like the glass front and side panel with a hinge, and the isolated area under the board for the power supply. I also like that it fit my Supermicro E-ATX dual cpu server motherboard. There was only 1 standoff hole that wasn't used, and it was within 2 inches of another standoff anyway, so no stability issues with mounting or board flex. I don't think I've owned a case before that had no external drive bay slots before, not that you need those nowadays. I knew it had none when I bought it, it it really didn't hit me until I started looking at accessories to buy and was seeing external drive bay stuff I couldn't buy that I would otherwise have. No biggie though.In all, just be aware of what you are buying this for, your budget, and its shortcomings and I don't think you will be dissatisfied if you keep your expectations reasonable. Just a word to the wise, if you weren't aware it does not come with fans, you might want to make sure you get all that figured out before you buy this case, because depending on what you are going to use it for, you may need a more custom configuration.

el gabiete esta bien pero no trae los ventiladores

good looking case not overly expensive amazing quality

I'm quite impressed by how above it weight (litteraly in that case) it punches. I've built my fair share of computer using far cheaper cases and far more expensive cases. It blows anything under a hundred bucks in terms of functionnality and ease of installation while almost holding up to my Fractal design. I just wanted to buy a cheap case for a computer that had to be in plain sight so I also wanted something that would look good and it's perfect for that.The good :- Easy to build in. It was a brease. Large space at the back for the cables, large cut out and mostly good placement for the rubber grommet.- Looks good.- Plenty of mounting hardware. Albeit no case fans so make sur you have that.- Fun to build in- Spacious, there's place for a 240mm rad at the top with enough clearance to run the cables, I had also enough space for a bigger hard drive cage to use it as a NAS.The bad :- Build quality is subpar. Paint chip off at the edges, feels awfully light when you take it out the box. Break out pci-e cover (they do include a replacement which I like).- It's a big case for it's class. Wider and taller. Makes it easier to work with but it's taking a lot of space.- No instruction, guidelines or whatsoever. You're on your own. Not a problem if you ever build a computer before but make sure you watch a couple of videos if you haven't.- Front panel is weird to remove and requires to much force I'm willing to put on such a slim tempered glass panelAll in all, I'm pretty satisfied and all the negatives are outweighted by the fun I had to build with it and the low price.

بدون مراوح

Very spacious to work in. I was not sure about the sturdiness, but that was a worry I should not have. The frame is very sturdy, no sharp edges. Was a bit cautious pulling the front glass off.Delivery: The box was fully intact, that is always my biggest worry. Glass has no chips and is fitting well.Is it a fish tank? I think it has some small surprises, for instance the grommets are well-placed. Paint quality is more than sufficient. I put in a full ATX board and there is plenty of space to put in a liquid cooler with three fans. The assembly was a bit tricky here and there, it is because I do not have a modular power supply. I would definitely recommend this case, if you like to look inside the computer. There is plenty of airflow as the front plate sits about 5mm away from the case. Yup, glad I put this together.Pro: Easy to assemble and build inCons: none so far.Edit: small update, I grabbed a bigger modular PSU and I just wish I could remove the disk cage without a drill (which I do not have).Still very pleased with the case, just need to learn cable management.