WLJH 10x Green T4.2 Neo Wedge Led 3030 Chipest 10mm Base Car Instrument Cluster Dashboard Gauge Bulb HVAC AC Heater Climate Control Lamps Switch Indication Interior Light Replacement

Worked excellent in what I was using them for. In a 02 Camaro headlight switch. Bright and nice looking now. Give an old dash a nice new look.

Wow, these worked for my Honda Accord 2009 AC lights, as recommended from a YouTube video. Nice and bright (in the picture, they are the ones where it says “dual” “auto” and “off”.) Only 6 of 10 bulbs worked but that’s ok because the 6 working bulbs is the price of ONE regular bulb at the dealership.

Needed to fix the switches on the HVAC controller in my old GS400. They would disappear at night, making it difficult to find the correct buttons to press to adjust the airflow. These bulbs fit perfectly, and all of them worked (no duds). I did install half of them opposite when I first installed them, because only half of them lit up (polarity matters). It helps to take a marker and put one dot on the back of the bulb. That way, if you need to remove the bulb and rotate it 180, it's easier to know which way it was in before your removed it (the bulbs are tiny, and they sometimes tumble when removed). The only way to know if the bulb is installed in the correct polarity is to reassemble the box and plug it in. These bulbs are bright, and there is no problem with the angle or direction of the LED bulb. All of the switches now light up a bright factory looking green. Maybe a bit too bright, but way better than no back lighting at all. The quality of the bulbs seems ok, and on par with the price. They did the job, and they all worked.

I needed bulbs for my 2008 Toyota Sienna Limited overhead console. The homelink buttons were not all lit up. My E/M, one dot and three dot buttons were not lighting up. I followed you tube directions to remove the two phillip head screws in the little pull down mirror compartment and then pulled down on the front two clips. Clips took some pulling to get out. Unclipped the electrical connectors and out it came. The bulbs twist out with a flat edge screwdriver. These bulbs have a cheaper mounting base than the original. Line up the base as best you can without the screwdriver. There are clips on each side of the base, line them up and gently use screwdriver to tighten. First time, I just put the bulb in the hole and stripped the screwdriver slot. Lining up the bulb is important. I put the three bulbs in and plugged in the front most electric connector to test before closing everything up. One of the three bulbs worked. As suggested in other comments. I marked the non-working bulbs with a marker on one side. I reinstalled the two 180 degrees (opposite) of the original installation and they worked. The bulbs are significantly brighter than the original bulbs (about twice as bright?). If it is important to have matching brightness you may want to replace all bulbs.

Bought for the climate control in an 09 accord lx. Pulled the dash piece and got the climate control unit out and apart to replace. If you’re doing this, be sure to install bulbs and loosely put back to tether to hook to power and test. Three out of five worked first try, two bulbs just needed to be rotated but i found two out of the pack that were not working when installed and/or rotated. I went with blue and think they look nice and just the right amount of brightness! It does look a little purple through the logos but it’s ok to me. At least i can see them at night. Bravo WLJH Video added one year later. Haven’t had time to open up and check contact points but i think the bulbs are prematurely failing. These are still good for the price point and i knew the risk i was taking so I’m still happy with them lasting a year

My original incandescent bulbs were vey dim even at full brightness and I couldn't see almost anything to tell which switch is for what. But since I got used to it, my fingers remembered which one is for what function. Finally I decided to replace old bulbs with these LEDs for both sides control pods. Although I wasn't inconvenienced by the old dim bulbs, I was shocked to see how bright these LEDs are and they are beautiful. These LEDs pictured are not at full brightness setting but somewhere in the middle brightness. I can't use full brightness. It's too bright. I've only used these LEDs for about 3 months but they look very durable, too. None of them has been dead so far. I highly recommend these LEDs. One advice is that as another reviewer suggested, keep your original light socket just in case. I don't know if these sockets are standard shaped but every time I buy similar LEDs, sockets are slightly different like thickness or else and they may be too tight or too loose. Led bulbs are attached to their sockets by winding feet a couple times, so if you use a picking tool, it's pretty easy to replace.

Works as expected. Had issues with few of the bulbs but the seller replaced the damaged bulbs.

Amazon said it was a perfect fit for me 2004 Ram 1500 but as you can see it wasn't... Now I am screwed out of time and money it spent to take off the AC, instrament, dome, overhead center console... So hopefully this helps other Ram owners like myself to not buy this item for their trucks...

Work good for international guage cluster and are very bright. Only downside is sometimes 10 isnt enough and you have to change them all and they are polarity sensitive.

En 6 mois d’utilisation, j’ai déjà eu 2 lampes qui ont grillé. De plus les ergots de maintien n’ont pas exactement la bonne forme, obligé de bricoler pour que ça tienne. Je ne recommande pas.

Actually you have to push little hard to tighten

Do not buy these for a 2003 Subaru Impreza, they do not fit🤬would have given Zero stars but not allowed.

Dont think they are burned out when you install them, test it before putting everything back, they only go in 1 way so if it wont turn on rotate it so the pads are on opposite sides. Diodes only let electricity travel in 1 direction so check that before returning the product.