2-Pack Soft Close Cabinet Drawer Damper for Metal Drawers/High-Quality Soft Close Drawer Adapter/Add-On/Retrofit, No Measuring Required! SCD104M (White)

These things are ingenious! They are easy - if a little tedious - to install and they function exactly as claimed. What an inexpensive and simple way to upgrade an older set of cabinets that are otherwise in great shape. I almost never write a product review but these little adapters are really great and I highly recommend them if you want soft close drawers.Here's a tip for installation that I figured out after finishing the 3rd drawer. Just set the 1st screw (the one that goes into the slotted opening) according to the instructions and then replace and close the drawer. The drawer will align the device exactly where it needs to be to affect the soft close. Gently remove the drawer and then set the 2nd screw and voila! Soft close drawers.

Once I read the directions thoroughly and watched a video on youtube, I was able to install these and they work great! My cabinets are old but in good shape (old Mills Pride) .

These are a great solution for metal frame drawers and mean you don't need all new drawers and slides just to get soft-close functionality (which could cost thousands). The slides are plastic though, with pretty thin looking springs, so I'm not sure about durability, but they're so economical you can buy some extras to replace just those on heavily used drawers (like the silverware drawer) if they don't last.Some of my packs were missing screws (and one had an extra screw) but none were missing other parts. You could easily substitute other screws from the hardware store if you don't want to hassle with returns.They make them pretty easy to install without measuring, but there are some tricks to make it easier:1. Install the tracks top-down so you don't drop sawdust into the tracks and springs of tracks installed below (this could get into the works and cause premature wear).2. Pre-populate the screws in the tracks before you place them in the cabinet (keep the tips flush with the back side of the track) so you can then just drive them in with a screw gun/impact driver and not need to worry about the screws falling off the bit.3. The track moves around when driving in the 1st screw in the slot (putting everything out of alignment). It's easier to put the back screw in first and use the slot with the front screw to fine tune the angle of the track to align with the tab on the drawer.4. Pull the sliding tabs forward on the track before putting in the drawer, else the drawer won't engage them properly.

Installation was moderately easy. Use the guide they give you and make 100% sure that it is square to your cabinet before screwing. I made the mistake of lacking squareness and the drawer did not close correctly. I easily fixed the mistake by making sure the guide is square before marking holes and screwing. Just a quick note: Always easier to pre drill laminate before attempting to screw it. Screws go into laminate much easier this way. All in all ,they work excellent for the money. Close nice slowly. I am gonna buy a few extra just incase one or two (hopefully not) break over the years.

This was pretty easy to install. I am not a very handy person but I watched the manufacturer's installation video on YouTube which is what made it so easy to install. I didn't even bother reading the paper instructions. It might help if you have a drill so that you can predrill some of the screw holes to make it easier for you but it's not totally required. They worked perfectly and didn't need any adjustments after installation. I'm very pleased and hope they last. Two of my drawers aren't too wide or heavy and the other two are the same width but taller and heavier. I only installed one of the adapters per drawer and they all seem to be working just fine. I would say if you have a very heavy drawer or one that is extra wide, you'll need to install 2 adapters per drawer. I'm now going to order more for my kitchen.

The media could not be loaded. This product is awesome! The drawers close perfectly and smooth. I only put 1 on my heaviest draw (silverware) and it works perfectly the instructions are great very easy to understand. I do recommend drilling a small pilot hole for the screws to make putting in the screws less frustrating. Also be careful with the guide setting tool for the inside of the cabinet the little prongs that attach to snap off easily.

These work excellent it takes a little adjusting but after you do one the rest go much easier. I recommend these to upgrade your drawers.

Unable to judge quality and functionality of product as I am not able to install damper. My drawers have slides mounted to bottom side of drawer and there for this item will not fit. This should be made very clear in description plus the tiny piece of paper showing somewhat of how to install these could not be read without the help of a magnifying class.