Question 1

What type of extension cable do I need for this chainsaw? I need about 15 to 20 meters but the manual says I need a 3mm cable for anything 16m or abov

Accepted Answer

All cables generate heat when carrying current due to the resistance of the conductors (I x I x R).  When uncoiled the heat escapes easily to the air. 1.5 square mm  cable is rated about 16 Amps uncoiled and 5 Amps when coiled on a reel. At 10.4 Amps (Full load of Oregon motor) the heat is 2.5 W per m. A 30 m cable will generate 75 W  and if coiled up there is insufficient escape for this heat power and the temperature can build up to damage the cable. Protection against electric shock should be by earth leakage trip (ELCB) as fuse protection is inadequate due to long thin cable and high risk outdoors. Use at least 1.5 square mm cable, uncoiled, with ELCB.

Question 2

Any one knows what length (size) for Oregon CS1400 's replacement chain please?

Accepted Answer

Look on Amazon page for the saw and select the option with spare chain. Chain spec is on chain package, 40 cm bar, 1.3 mm gauge, 3/8 inch pitch low profile, 56 links. Several Oregon chains of different qualities suit, example 91VXL056 and 91P056. An E at the end just describes the packaging.

Question 3

Problems attaching bar and chain with one I've just purchased. The tensioner does not move far enough to fit the chain. Any tips?

Accepted Answer

You seem to expect to be able to put the chain into the groove on the bar without taking into account that the path length for the chain within the groove is much shorter than the path around the top of the walls of the groove. If the chain length were made so big that it was easy to just lift it into the groove there would be far too much slack once it is in the groove. Benno's comparison to putting on a bicycle chain is very good. You need to get as much as possible of the chain around the drive sprocket, into the lower groove, around the tip sprocket and up into the upper groove and then pull the chain that is in the upper groove further along the groove (in reverse) to get more chain in. This will cause the drive sprocket to rotate in reverse. When all the chain is in there will be a lot of slack to take up by the tensioner.
An alternative method is to first put the chain fully and tightly on the bar with the bar in your hand and the tensioner wheel fully anticlockwise. With the chain tightly in the groove you will have just enough slack at the back end to put the chain over the drive sprocket and then get the bar over the stud. During this last manoeuvre it may be necessary to allow the chain to slide on the bar in order for the drive links to get properly onto the drive sprocket. Take up the slack with the tensioner. Fit the side cover and pull the chain in reverse to ensure it is correctly mounted and moves smoothly with effort in order to avoid damage when you power up. When pulling the chain make sure the left hand barrier (Brake) is pushed towards the motor). Prime the oiler and oil the front sprocket BEFORE you fit the chain. Pulling the chain in reverse will help you judge the tension. Too much tension will make the chain very difficult to move and will wear the bar. Too little will risk the chain jumping out of the groove.
Amazon sell the saw with chain M91VXL056, Pitch 3/8, Gauge 0.05 inch 1.3mm, 56 drive links. Any chain with those parameters will fit. Those values are on the chain packaging.

Question 4

How many chain links? (56 or 57?)

Accepted Answer

Look on Amazon page for the saw and select the option with spare chain. Chain spec is on chain package picture, 40 cm bar, 1.3 mm gauge, 3/8 inch pitch low profile, 56 links. Several Oregon chains of different qualities suit, example 91VXL056 and 91P056. A letter at the end just describes the packaging. I have the saw and several different qualities of Oregon chain so I am sure.

ASIN	B07SSQ74V2
Best Sellers Rank	4,070 in Garden ( See Top 100 in Garden ) 15 in Chain Saws
Brand	Oregon
Country of Origin	China
Customer Reviews	4.4 4.4 out of 5 stars (1,558)
Horsepower	2400 Watts
Included Components	1 x Electric Corded Chainsaw
Item Dimensions L x W x H	25L x 27.5W x 53H centimetres
Item Highlight	ControlCut Technology, Lightweight, Quiet & Low Kickback Chainsaw, with Automatic Oiler, 3-Year Warranty (CS1400)
Item Type Name	Chainsaw
Item Weight	6.61 kg
Manufacturer	Oregon Tool
Manufacturer Warranty Description	3 years manufacturer.
Model Number	CS1400
Number of Items	1
Part Number	CS1400
Power source	Corded Electric
Unit Count	1.0 count

Oregon 2400W Corded Electric Chainsaw with 16" Guide Bar & Saw Chain

Details

Details

Description

Specifications

Common Questions