Crankset Single Speed 44T 170mm Crankarms 110 BCD Crankset for Mountain Road Bike Fixed Gear Bicycle(Square Taper, Black) (44T Sprocket)

This is a 44t single chainring crankset. If you have a 68mm square-taper bottom bracket on your bike, this is "plug-and-play". It is a 5-bolt 110bcd chainring, cranks are 170mm. I used it to replace the 3spd front cranks on my Trek Verve 1 to make the bike a 1x7 drivetrain instead of 3x7. I just don't like dealing with a front deraileur. It fit right into place, no problem. One thing to note: while the crank arm attached to the chainring is non-removable (it is riveted in place), the chainring is held in by standard chainring bolts! That means if the 44t ring is not right for your bike, you can order another 110bcd 5-bolt chainring and swap it out!!! I eventually did this, replaced the 44 with a 42t chainring. Even better, while the stock chainring is installed on the "outside" of the bolt-arms, you can install it on the "inside" so it sits 1-2mm closer to the frame to get your chainline right. A very small adjustment, but it is there.

Edit: Be careful with the threads. They are likely to strip quite easily. Now I can't get the non-driveside crankarm off - I've probably pulled a square taper crank off 10 times, and this is the first I've stripped. Original: If you are trying to set up an inexpensive "1x" bike, this is most likely what you're looking for. This is a great-value square taper crankset with a removable chainring. The bolts are not riveted, so you can remove the chainring with a metric hex key and thin spanner wrench (or adjustable wrench, your choice). Just be careful enough not to strip the nuts holding each bolt. I re-tightened to 6-7 Nm. I replaced its 1/8" ring with a 3/32" USAMade since 3/32 is standard for shifting drivetrains. If you're wanting to use this crankset as-is on a bike that shifts gears but don't want to change the ring (it's easy though), you must replace your 3/32" chain with a 1/8" chain instead. Other things: It's decently lightweight (cranks 495 g, chainring 242 g). The pedal holes feel tight at first, but as long as you're installing your 9/16" pedals straight on and with lube, you can avoid stripping threads. When installing onto the bottom bracket, I would lube under the bolt's head, washer, and threads (but not the taper), and also where the bottom of the bolt head makes contact with the center of the crank.

Unfortunately I had to return it as it did not fit on the set up that I had. Per the description it was supposed to fit but it did not. Ended up taking it to a bike shop and they repaired it $175 late.

Needed a 110bcd crankset as I have many chain rings for it. It's ok but the black coating was peeling before I even rode on it maybe I should have got silver. I do like that the ring can be mounted on both sides depending on your BB width.

Nice looking, and it has no logos. But it requires a very short bottom bracket. Even with a 103mm bottom bracket and moving the ring to the inside of the spider, the chain line is poor on a bike with a 130mm OLD rear triangle. It might work with a modern 142 or 148 OLD bike.

With the right tools, this is an easy install but you have to have the right tool to pull off your old crankset. I bough this more for the ability to change out sprockets as my cheapo bike had a fixed sprocket/crankset setup and it was perfect for that. My bike is now easier to pedal as I was able to put the right size sprocket on.

You need a crankset key to get your old crankset off in order to install a new one. Fit perfectly

Does not fit standard fixed gear spacing (42mm chainline with 120mm rear). Even with the chainring mounted to the inner location, it measures 50mm as pictured. Based on this, I'm guessing this is for only MTB single speed (i.e. 52mm chainline with 135mm rear), not road single speed or fixed gear.

Flaws in the paint, and some scratching straight out of the box. Does not include crank arm bolts. The CDHpower text is quite large on the arms. Fit fine, and pedal threads were fine.

Not bad for the price. The paint was a bit scratched and I only received one of the two plastic caps. Q factor a bit wider than expected. But it does the job and the chainring is rigid and straigth.

I wish I read all of the reviews. There was one person complaining the teeth are not correctly spaced and that’s exactly my situation. Chains won’t fit. There were also reviews about a stripped pedal thread and I also experienced that. 0 stars, I want my money back

Threading on drive side crank arm has pulled out almost detaching the pedal after less than 150 km of use on a single speed cruiser bike, genuinely unsafe product do not purchase.