Height Adjustable Speaker Stands for Bookshelf Speakers | Universal Fit, 11 lbs Capacity, Set of 2 for Bose Polk JBL Sony Yamaha - 42" Max Height

Good speaker stands to enhance listening. I liked that they came with the hardware to mount the speakers a couple different ways, that they can be adjusted for height, appear sturdy and support heavier speakers without tipping over. My speakers are shaped differently than most others but I was still able to get them mounted. They also have the feature to hide any wires. Easily assembled in very little time. These look great with my decor and don't take up a lot of space.

I bought the Mounting Dream Black Alloy Steel Speaker Stands specifically for my Samsung HW-Q990B rear speakers, and they’ve exceeded expectations. The stands are not only sleek and sturdy, but they also support the odd mounting needs of the Q990B speakers with a little customization. I used a 1/4"-20 screw from Home Depot, and the fit was spot-on. The adjustable height made it easy to position the speakers at ear level, which noticeably improved the surround sound experience. Cable management was a bit tricky due to the Q990B’s power cable design, but with a couple of extension cords and some creative routing, I got a clean setup that looks great and performs even better.

A well built, easy to assemble, adjustable height stand. As other Sony SA-RS5 reviews have noted, you need to go to a hardware store and purchase 5mm screws. As I wanted to mount the speaker right away, I used the keyhole screw to attach the speaker. The problem with this method, and even with a 5mm screw set up, as you tighten it down the sliding rod bends and kicks the bottom of the speaker away from the bar. Two Tips: One, borrowed from Jamie, another reviewer, was to saw off the bottom of the support loop. After ensuring that I had the speaker where I wanted it, and making sure that the support rod was flat against the speaker, I simply wrapped a piece of scotch tape at the bottom of the lower support (the one with 2 screws), removed the support from the speaker and hack sawed it off about 1/16 inch above the tape. I filed any sharp edges. I didn't paint the exposed metal as cutting it above the tape line the support rod is completely hidden withing the bracket. Do yourself a favor. Cut the rod. It's ugly as sin hanging below the speaker. Tip 2: I cut the included plastic spacers in half with a coping saw and then sanded any burrs. I only eyeballed the center and it worked out. I then took the "half" spacer and placed it between the speaker and the support rod. I used a 5mm x 16 cap head screw as they're black and match the stand. This size screw allowed 3 to 4 good thread bites into the speaker which firmly supported it. A 5mm x 20 screw would offer more bite but isn't necessary. If you buy a cap head screw, you'll need a smaller sized allen wrench than the one included with the stand. Using the 1/2 spacer enabled the bar to sit completely flat against the speaker with no bend or kick out. If you don't want to cut the included spacer, use a 1/2" hard rubber spacer from a big box store. They'd be in the specialty hardware section. You may even find them here on Amazon. I wasn't crazy about the plastic feet so I attached felt pads to them. This helped to protect the hardwood floor and gave the added benefit of allowing the power cord to be placed anywhere under the stand bottom. If you have Sony SA-RS5 speakers, you'll need to purchase 5mm screws to secure them to the stand, but these are great, solid, stable stands and worth the money.

I got two sets of stands (4 units), added a few silicone pads and Velcro cables ties via Amazon, and now have perfect mounts for the four Quad speakers. The stands are high quality, easy to assemble and versatile. Mounting Dream MD5042-2 speaker stands can be a good solution for mounting Sony Bravia Theatre Quad speakers. Cost is now about $80 for two stands; I got two sets via Amazon and added a couple items to get the kind of mounting I wanted. The stands allow for multiple mounting approaches, but the Quads are of unusual design, so I added two items below for mounting the Quads (I mounted the Quads with their Sony table-stands attached): 1. Rubber mounting pads: Hudson Hi-Fi 1" Platinum Silicone Isolation Dot, Non-Skid Isolation Feet - With adhesive back - 20 Duro - 16 Pack (via Amazon, $18). Stick four dots on top plate of each stand to support the Quad-stands (align dots with edge of mounting plate). 2. Cable ties: VELCRO Brand ECO Collection | 5 Inch Small Straps for Cords | Reusable Cable Ties | 3/8" Wide, Black, 50 Pac (also from Amazon, about $12). Thread 4 cables ties through the four, 4mm slots in the speaker mounting plate and tighten to secure the speakers on top of the isolation dots. Make sure you’ve installed power cord before mounting speaker. The Mounting Dream speaker height is adjustable and the plastic base-feet are adjustable to correct for uneven floors. The base is “domed” so excess speaker power cord can be coiled and hidden under the base plate. The speaker power cord is hidden inside the support tube. One needs to pull the speaker-end of power cord up through vertical support tube (internal structure of tube prevents gravity feed of speaker-end of power cord). I used an electrician’s fish-tape wire-puller. Something like an undone wire coat hanger would also work. I used twist-ties (from plastic food bags) to temporarily attach the power cord to the fish tape for the pull-thru. Note that the Mounting Dream speaker mounting plate is barely large enough to accommodate the Sony-stand, so use care in aligning silicone dots and speaker base. The isolation dots should align with edge of the mounting plate. You won’t need the MD5042 “Speaker Attachment Unit” using the mounting approach described here (you’d only need this if using back-of-speaker mounting hole … a whole different, off-centerline mounting method).

These fit the Q990D speakers perfectly. Setup was easy and the hidden cable management tubing makes the whole setup a lot more discreet in the living room. Build quality is a hefty, sturdy metal, have had a few weeks now running vacuums over and so forth and no scratches display. This stand allowed me to shift speakers behind sofa and to a proper height, which unlocked the surround sound bubble of the Q990D.

Works well enough with my new Sony RS5's. These are on the heavy side for satellites (claimed 5.5lbs) so I wanted something with a base vs just hanging from an offset pole. When mounted and secured as shown, they're secure enough for my satisfaction - but I also don't have a large dog or kids to worry about. Just a lazy cat and robot vacc with a mind of its own. If I did, I think I'd put a bar weight over the post, onto the base. In the pictures it's important to note that I cut the wire loop bracket used to secure to the rear of the speaker. Normally it would be extending down past the base another 7inches or so. In addition the fore and aft adjustment bracket stuck out from the front of the base plate a good inch or so. Not aestetically pleasing. So I have no intention of using these stands with any other speakers, so I just cut them with a hacksaw, sanded the rough edges on a belt sander, and gave the edges a quick shot of black spraypaint. I'm *very* tempted to take a grinding wheel and contour the base so you don't see the corners sticking out from beneith the speaker. This is the compromise in using a stand more tailored toward small bookshelf speakers: the square base will show. For now I just wanted to get them setup so I'll save that for a rainy day. Power cable is annoyingly short, but that's not the fault of these stands. Still a good 18-20" of cord at the foot of the stand when they're extended to roughly 35" (to bottom of speaker). The right angle plug and choke dropped down the tube without any issue. Ultimately I'm happy - I know these stands were going for about twenty less this time last year, but at $35/stand it's still cheaper, and more versatile, than using accent tables.

Assembly requires lining up threaded holes in the interior pipe with unthreaded holes in larger outer pipe and using the hex wrench to screw the pipes together. Typical but a bit fiddly for me 'ol hands. Also black-on-black hard to see. Better would be a slot in the outer pipe and ready-set bolts sticking out from the inner which slide into the slot and are tightened with a strong wingnut. No fiddly tool needed. Same for the upper connection which is slightly but not fatally out of align likely due to the crimping of the inner pipe which inevitable shortens it by a 1/16th inch or so. As the threaded holes were likely set in prior to crimping, this moves them down a tad versus the outer pipe holes which were punched with a certain alignment that is not there after crimping. Net: slight misalignment not fatal but do not expect the holes to be properly centered. Just push real hard on the top pipe to encourage alignment as best you can. Back speaker support bracket adjusts horizontally and vertically. High enough for my Polks and design permits wires from wire posts to pass through unobstructed. This is a very clever, unique, successful design. So we now have 2 very strong and satisfactory speaker posts. Well worth the money. Might spray white Rustoleum on them to blend with the wall and replace speaker fabric with white available right here on AMZN. Then we would have something truly superb. Net: these posts are very good. Buy them, say we.

After CAREFULLY researching stands for weeks I decided to pull the trigger on these, despite knowing I was going to have to do some modifications to make them perfect for my Klipsch Reference Cinema 5.1.4 speakers. First off the four round feet on the bottom of the stand are NOT rubber they are plastic. I had to buy rubber non skid pads and cut them down to fit. I knew this before I bought them so I wasn't surprised. I also had to buy four 1/4 in 20 x 1 in screws and washers to mount my speakers to the stands. (Pic 1) While all of this sounds like a pain in the butt it's not a big deal if you want them to look nice. The vertical sliding bar that you put the screw through to mount the speaker would hang down otherwise, and IMO look awful. Oh and the screws it came with did not fit in my speaker, despite being the same exact size as the ones that I bought. Overall this product is still MUCH better than any other stand I could have chosen. The Klipsch Reference satellites are not perfectly rectangular. They get a tiny bit smaller in size towards the back of the speaker. This means that none of the clamp type stands will work. You have to find a stand that you can mount it to. I wouldn't want to use a crappy stand that squeezes my speaker anyway. The stands are pretty firm and stable. I am not worried about it getting knocked over and I pets. My only other gripe is that the wires get smushed against the bottom of the mounting piece if you want to move your speaker back far. However it was easy to just move it forward a MM or two and ease up on the cord being crushed. You can adjust the size of the actual part that the speaker stands on to make it bigger to fit a speaker like this. That made me very happy. It's very balanced now. The stands are very straight and look great. I am incredibly happy overall with this purchase. I am SO grateful for the other guy who left the review mentioning these speakers. Such invaluable information when you're trying to browse through a couple crappy speaker stand options on Amazon. Definitely would buy again if I had to.

Good product

Excellent quality product. Easy to assemble and fix. Several options for different size and types of speakers

This is the kind of purchase that makes one happy. The box is neatly and tightly packed. Each item is labeled well, and the instruction manual is clear as day. The product contains everything you'll need to set up most of your speakers (except wood screws). Unfortunately, my satellite speakers are a millimeter too tall to aptly secure from the back, but that was easily remedied by a thick double tape (instead of using wood screws from the bottom). Edit: there's a slight wobble on my tiled floor which I can't see to get rid of no matter how much I try to adjust the feet. Since the base isn't heavy, there is a mild risk of tipping over. Something to consider if you have kids.

I have received the consignment. It arrived in very good order & I thank you for your excellent service for the rapid delivery, well done. I am extremely happy with the product, it is exactly as I expected & as advertised. It is robust, simple to assemble & of great quality. I would highly recommend this product to future & current Samsung customers looking for rear speaker support stands.

Good speaker stand for holding heavier speakers.