POWERTEC 120/230V Dual Voltage, 28 Amps, On/Off Switch, Single Phase Safety Power Switch for Table Saw, Router Table, Drill Press, Bench Saw, Bandsaw, Grinder & Other Electrical Equipments (71008)

Works pretty well over all. Wiring was easy to connect with standard spade terminals but I could also have used ring terminals. I have a vintage drill press of unknown manufacture and was surprised to find that the switch actually fit the mounting hole, however the cover and the paddle were both too large but I was easily able to trim them down a bit with a multi tool. I would have been surprised if it had actually fit perfectly on my old drill press but it definitely works well and the modifications that I had to make were purely cosmetic. The cover seems very sturdy and durable as well, definitely wouldn't break easily under normal usage. I'd buy another one of these if I ever end up restoring another machine that needs a power switch.

Works great for our purpose. Easy to see with a huge stop paddle. Would buy again.

The switch does what it should. I'm using it on a 2 HP 220V motor on my table saw. Easily wired and easy mounting. Would buy again for other machines if needed.

I bought this switch to replace switching capability on an old Craftsman saw where replacements for the OEM switch are unavailable. The features are similar: recessed "ON" button that can be locked out, 120/230 compatibility. Overall I like the switch and installed it successfully, but there are some issues with this product listing and compatibility with POWERTEC's own switch box. Pros: 1️⃣ It's a nice solid switch with 120/230V compatibility. 2️⃣ The tactile characteristics of the switch are good. It gives a nice "thunk" when turned on or off, and in the case of my 10A saw, it seems to be a good steady connection. 3️⃣ Clamping screw terminals for fork terminal connectors. These inspire much more confidence than spade terminals, assuming you use good quality crimp connectors installed correctly. Another review suggested ring terminals and I disagree. That's not what this is designed for. Cons: 1️⃣ The cover plate is awkward. It has to mounted perfectly for the switch to work properly, but the cover is mounted to the switch using the same screw holes that mount the switch to the box, and the cover doesn't clamp directly to the switch, but relies on the stiffness of the plastic cover for strength. This is bad for durability and also makes installing the switch a pain, because the switch floats inside the box until you manage to get everything screwed together. 2️⃣ The switch doesn't fit on the POWERTEC switch box without destructive modifications, despite claims of compatibility. 3️⃣ There's not a *good* way of attaching ground across the switch unless you use a metal box. Some documentation shows the ground attached across one of the top bracket screws, but in practice this is awkward due to space constraints. 4️⃣ This claim from the product details seems to be false: MAGNETIC SAFETY FEATURE: Equipped with a magnetic switch that prevents automatic restart after power loss or outage. Ensures your tools remain off until manually restarted, protecting both operator and equipment. I had my suspicions, because usually you have to choose between dual voltage compatibility and electromagnetic switching, because the electromagnet has to be calibrated to the voltage. But ... y'know ... still hoped, because I want both of those features on this tool if I can have both. In any event it doesn't work. If I turn the switch on, cut power to the circuit, then restore power, the switch is still on. Either this switch is defective or the product details inaccurately claim a magnetic safety feature.

Good value. Seems to be made pretty well. Been working fine so far.

This was a SCORE ! The power switch on my Grizzly 5500 band saw finally gave out after about 6 years. Browsing the Amazon feed for a replacement and saw this Powertech replacement that looked just like the one I needed. Sure enough this was a direct replacement and works as it should. I 100% endorse this part and its compatibility with the Grizzly 5500. Thanks, Jim K.

Rewired my 3-in-1 Mill-Drill-Lathe and used this to replace the OEM switch. The original switch was overly complicated and fragile. This is a sturdy, sensible replacement and much easier to wire into the system. Great value. I wish they had a option with lighted buttons (not necessary but would be a welcome addition).

This is really not suited to mounting in a standard electrical box though the mounting screw spacing matches that of most boxes. The terminals are small screws and are unsuited to use with solid building wire. Ring terminals are the only safe option and there is sufficient clearance only for terminals for 14 gauge wire and smaller. Solid wire is too stiff. Terminals will be overstressed by bending forces when installing the switch. Flexible stranded wire as in cordage is required. Fortunately for me that's what I was planning to use. The front panel/button assembly is not fastened to the switch assembly. The switch assembly is simply clamped between the button assembly and whatever it is mounted on. This makes for a fussy, difficult assembly in an electrical box. Clearances need to be just right or the buttons won't function properly. The switch is big. It is not too wide, but it is unusually long and very deep. Die-cast outdoor boxes won't take it without modification. I made it work, but I have a milling machine, know how to use it and wasted over an hour modifying a box by milling away hubs and bosses that were in the way. It was still a very tight fit that required a plastic sheet behind the switch for insulation. This thing is more suited to mounting on a machine panel with plenty of clearance around it and behind it. The switch itself seems solid and carries a UL label. I wouldn't buy it again unless I was planning to panel mount it.

High quality & functionality product.

Apenas me acaba de llegar, al destaparlo se nota que es de buena calidad, es ideal para erramienta de alto rendimiento. Me gusto en especial por qué ya contamos con otro tipo de apagadores y dicen ser de uso rudo, y en el mismo plástico parece de muy baja calidad. Pero este producto se ve resistente y de muy buena calidad. Excelente compra para su uso en maquinaria, me sorprende que en un costado trae una calca, donde según dice que puede aguantar hasta para 10 Hp. Yo lo usaré para un motor eléctrico marca WEG cerrado de 3HP. Los retroalimento en cualquier detalle.

Haven’t put power through it yet but it lakes great in the shop and feels like a quality component. It is rather deep, mounted mine in a 4” x 4” box.

Es un buen producto, buena relación calidad precio, cumple con su función de encender y apagar con protección, es sencillo, no tiene que ser complicado. Solo se tiene que comprar las terminales para poder conectar los cables, no tiene porque traerlas en la compra ya que muchas veces los cables originales deben traerlas. Muy satisfecho con la compra. Gracias.

This safety switch was just what I was looking for, the function is just what you would find on brand name products for safety. I made this stand for a DeWalt port-a-band, and wanted it to look professional. Easy to install, this switch gave it that look and function.