[4 Pack] Galaxy S10 Plus S10 Camera Screen Protector, 0.2MM Ultra Thin HD Organic Tempered Glass Camera Lens Protector for Samsung Galaxy S10 Plus/S10

I've waited to write a review because I wanted to see how the product would hold up over time, and I could not be happier. I purchased this in April, 2021 and it still looks brand new on my phone. Not a scratch on it and the adhesive is just as strong as the day I put it on. I still have the other lens cover from the two pack, just waiting on this one to break (from the many times I drop my phone) become lose around the edges, or lose the quality of my pictures due to simple wear and tear lens protector itself. But, nope. Still going strong!! Great purchase. Easy to install and incredible, LONG LASTING, quality. Will 100% buy again (hell, if I ever need to 😏)

Easy install. There are 4 dust removal stickers 4 sets of wet and dry wipes.I was a little confused when i received square sealed lens protector. However, It clearly said that bend over the back board to take off the actual protector.Really straight forward. If you are careful enough. You will be able to install this with one try. (I did it on 2nd)If you mess it up on the first trial, just use dust removal sticker to take the lens protector off(partially attached on the protector.)3rd picture is the picture that i took after i install the lens protector. no dust inside clean. There are no image differences. Pixels are well defined even with lens protector on.Highly recommended.

I wanted a camera protector for my new Samsung Galaxy S10+ so I got these to try it out. The product came with 4 protectors, cleaning wipes, and dust stickers. I cleaned my phone's camera carefully, making sure there are no dust on the lens. Then following each step on the package to put the protector correctly. The instructions are clear and simple. The toughest part aligning the protector against the camera. I slowly hover the protecter slightly above the camera lens to align the left and right sides then checking for the corners. When all is well, I pressed down from the center and the bubbles and air would escape to the sides.I really like the result because I can barely tell that I have a protecter on 😎

So far its a great product ! I was very doubtful since many reviews say that the protective lence affects the clarity of the images but it doesn't really do that at all. The instructions are a bit difficult to understand but once you get the hang of it, its an easy installation. And the extra lenses are a plus as well!

Most of the reviews I saw when I bought this lens protector were brief, non-specific, and had no photos. That should've been my heads-up that they're mostly fake...This thing is a PITA to put on. It comes with no instructions, so the first one was a throw away practice attempt. I got close to adhering it but it slightly warped when I tried to put it on and it never finished sticking. That seemed impossible for a small piece of plastic but it did.I have no idea why those rectangular, Tetris-shaped backing pieces are included. They look like they're cut out for a reason but I can't figure out why. They don't have guidelines. Not sure why they aren't see through. I had to figure out where the protector's edges were so I could apply them. The backing should outline the protector so I know where the heck it is. The guide stickers didn't stick to the protector so I could move it over the target location. I had to pry an edge up (near the flash opening side in case it warped again) to get it off the backing.I've installed dozens of these tempered glass and film type protectors to phones, cameras, DSLRs and PDAs over the years and never saw one with as dumb an application process as this one.Instructions might've helped, but I'm not even sure about that.Good luck finding an actual tempered glass alternative to this one though.When my husband installs his, he'll probably need one for practice also. So a four pack is a two pack at best.

I was hesitant about getting these because I seen other reviews about pic quality after they were on..... well I have NO issues with pic quality, it doesn't seem to interfere at all with it. Make sure you do each step completely and if you are using a case take the case off to put the protector on (it'll make it easier to get on). Clean your screen with the wet wipe they give then dry it off with the dry wipe the provide. Make sure you use the duster sticker after this (I tacked it a few times) then I peeled off the protector film off the protector (there's a clear film on the protector to protect it)... then I actually took the small protector off the black cardboard area I did not lay the whole thing over my phone I carefully placed the protector over my camera starting with the side that has the cut out for the flash 1st then laid the rest of it down.... to me it seemed more of a suction type of way it sticks to the screen by the way it felt when I placed out on the lens, but it laid down fine for me, NO bubbles, no dust, no fingerprints (because you dont touch the underside of it) and NO issue with any pic quality change. I have had it on my phone now for a bit, still no issues. All I can say is if you have an issue then it is user error.... So far so good and seems to be doing its job.

I was hoping that this one would be a good one since I was reading some good reviews. I received the item and the first thing I noticed was that the box and item itself was different than the one in review photos and the item description phoyo. Other discrepancies were the cutout for the flash and heart rate monitor were different from the photo. All of this could've been forgiven if the product worked. However like many other lens protectors it causes a blue haze with the flash turned on.I took it off and to my surprise it's not glass! It's plastic! I think that the positive reviews came from a different batch (as they came in a completely different box as shown in the photos). So I returned them sadly.Photos taken shows before the protector and after. You can see the haze created by the flash